Manuals / Excell Precision / Personal Care / Scale

Excell Precision Counting Scale user manual Auto Calibration, Zero Function

Models: Counting Scale

1 46

Download 46 pages 23.15 Kb

Page 14

2-5 AUTO CALIBRATION

EXCELL PRECISION CO., LTD.

2-5 AUTO CALIBRATION

Œ When the scale is at zero, press and hold . followed by pressing U.W. PST until the weight display shows the scale capacity flashing, then release the keys.

→0← 3	.	.
→0← 3
		Stable 3

Value of full capacity of the scale

•Place weights on the scale equivalent to full load capacity. When the scale is stable, it will calibrate automatically. While the scale is counting back to zero, remove all the weights from the scale. The Calibration procedure is finished.

4If full load is not available in weights it is possible to enter a weight value of less than full load. Enter the weight value to be used and then place the weight on the scale, when the reading is stable the scale will automatically calibrate.

While the scale is counting back to zero, remove all the weights from the scale. The Calibration procedure is finished. The new calibration will be stored and recalled when the scale is switched off and on again.

Press

CE

key to exit from the calibration mode.

4Restore to the default setting: When the Auto calibration is miss-operated, and

the scale should be restored to the default setting, please hold CE key and press U.W. PST key, the default setting will be restored after the scale counting back to zero.

2-6 ZERO FUNCTION

Press the Z key to re-zero the display with no load on the weigh pan. When the zero is set correctly the “3” icon will be displayed adjacent to the (à0ß) symbol on the weight display.

The zero setting range is ± 2% of the capacity of the scale.

Counting

12

ZSME200000003

Image 14

Excell Precision Counting Scale user manual Auto Calibration, Zero Function

Contents

USER MANUAL Page ZSME200000003 TABLE OF CONTENTSCounting CHAPTER 4 KEYBOARD TYPES INSTRUCTIONS FOR USE PREPARING TO USE THE SCALE1-1 DISPLAYS SYMBOL ICONS “3”CHAPTER 1 PRODUCT INTRODUCTION DIGITAL DISPLAYSZSME200000003 d=divisionCounting ADDITIONAL FUNCTIONS TYPE I ⇒ Dual Weighing Unit 1-2 KEYBOARD FUNCTIONSTANDARD TYPE 7 8 9 SMPL Q’TY PSTCounting ADDITIONAL FUNCTIONS TYPE II ⇒ Unit Weight Preset7 8 9 SMPL Q’TY PST 4 5 6 UNIT U.W W.T. PST ZSME200000003This is a dual function key which selects COMBINATION TYPE ⇒ Dual Weighing Units + Preset Piece Weight Stores7 8 9 SMPL Q’TY PST 4 5 6 UNIT U.W W.T. PST CountingPower Consumption 1-3 POWER SOURCESApplicable Power Sources Low Power WarningCHAPTER 2 OPERATION 2-1 SWITCH SCALE ON2-2 SWITCH SCALE OFF 2-3 DISPLAY BACKLIGHT2-4 SAMPLING SPEED & BACK TO ZERO SETTING 2-5 AUTO CALIBRATION 2-6 ZERO FUNCTION2-7 UNIT WEIGHT CALIBRATION SMPL2-8 COUNTING 2-8-1 The Unit Weight of Object is Unknown2-8-2 The Unit Weight of Object is Known ï ð2-9-2 Clear Tare Value 2-9 DEDUCTION OF CONTAINER WEIGHT2-9-1 The Weight of Container is Unknown Tare 2-9-3 The Weight Container is Known Pre-set Tare ZSME200000003 2-9-4 Clear The Pretare ValueCounting 2-10 TOTALISING 2-10-1 Quantity totalising2-10-2 Recall Quantity Totalised 2-10-3 Weight Totalising2-10-4 Recall Weight Total Counting 2-10-5 Clear all Totalised ValuesNOTE All totals will be lost if the scale is switched off ZSME2000000033-2 PRE-SET TARE CHAPTER 3 USER INTERFACE SETTINGKEY ACTION 0 = M+ will be operate when the weight is stable 3-3 PRE-SET QUANTITY CONDITIONSOPERATION 3-5 M+ CONTINUOUS OPERATION Only After Return to Zero 3-6 MULTIPLE UAGE KEY U.W.PST / kg/lb FUNCTION SELECTIONZSME200000003 the scaleCounting 2 = Transmit only when weight is stable 3 = For EZ-2 printer 3-7 BAUD RATE SETTING for only with the serial interfaceTransmit mode 0 = Press M+ to transmit 1 = Continuous transmission4-1 STANDARD TYPE 4-1-1 Quantity PresetCHAPTER 4 KEYBOARD TYPES 4-2-1 Unit Selection 4-2-2 Quantity Preset4-2 TYPE I ⇒ DUAL WEIGHING UNIT Clear the Hi Limit unit weight and quantity values 4-2-3 Weight PresetSet the Hi Limit value for unit Weight Q’TY PST4-3 TYPE II ⇒ UNIT WEIGHT PRESET 4-3-1 Unit Weight Preset StoresQ’TY PST 4-3-2 Quantity PresetHi Limit Value for Quantity Preset SMPLClear the Hi Limit unit weight and quantity values 4-3-3 Weight PresetSet the Hi Limit value for unit Weight Q’TY PST4-4-1 Unit Selection 4-4 COMBINATION TYPE ⇒ DUAL WEIGHING UNIT + UNIT WEIGHT PRESETQ’TY SMPLRecall the Unit Weight Preset 4-4-2 Unit Weight Preset StoresSet Unit Weight Preset Q’TY PST 4-4-3 Quantity PresetSet the Hi Limit Value for Quantity Preset SMPLClear the Hi Limit unit weight and quantity values 4-4-4 Weight PresetSet the Hi Limit value for unit Weight Q’TY PSTCHAPTER 5 INTERFACE 5-1 TOTALISING5-2 PRESET TARE OPERATION CONDITIONS Use the number keys 0 or 1 key to select 0 or0 or 1 to select 0 or 5-3 QUANTITY PRESET OPERATION CONDITIONSUse the number keys 5-4 TOTALISING OPERATION CONDITIONS Use the number keys 0 or 1 to select 0 or5-5 THE CONDITION TO ALLOW THE NEXT TOTALISING OPERATION 5-6 COMBINATION KEY OPERATION MODE 5-7 BAUD RATE SETTING 0 ⇒ 1 ⇒ 2 ⇒ 3 ⇒5-8 TRANSMIT MODE SELECTION T/A⇒Total Amount NO.⇒No. of totalising operations N/W⇒Net Weight U/W⇒Unit WeightPCS⇒Piece T/N⇒Total no. of totalising operations T/W⇒Total Weight Counting