Manuals / Excell Precision / Personal Care / Scale

Excell Precision Counting Scale user manual Unit Weight Calibration, Smpl

Models: Counting Scale

1 46

Download 46 pages 23.15 Kb

Page 15

Image 15

EXCELL PRECISION CO., LTD.

2-7 UNIT WEIGHT CALIBRATION

♦Two methods of unit weight calibration are available depending on the scale configuration they are either:-

1.Auto Calibration ⇒ if weight is over 10% of the last sampling value, the scale will automatically re-calculate the unit weight.

Example:

Say the current unit weight is 2.5g. If the next batch of product of the same type has a slightly different unit weight say 2.8g, then because the difference between the to unit weights is greater than 10% the scale will average the two values and set a new unit weight of 2.65g. If the difference in unit weights are less than 10% then the unit weight is not re-calculated.

2. Manual Calibration ⇒ Press

SMPL

key to determine the unit weight.

♦The Auto Unit Weight calibration is setting is a factory set option. If it is set to off then the auto unit weight calculation is disabled.

Counting

ZSME200000003

Page 15

Image 15

Excell Precision Counting Scale user manual Unit Weight Calibration, Smpl

Contents

USER MANUAL Page TABLE OF CONTENTS CountingZSME200000003 CHAPTER 4 KEYBOARD TYPES PREPARING TO USE THE SCALE INSTRUCTIONS FOR USEDIGITAL DISPLAYS SYMBOL ICONS “3”CHAPTER 1 PRODUCT INTRODUCTION 1-1 DISPLAYSd=division CountingZSME200000003 7 8 9 SMPL Q’TY PST 1-2 KEYBOARD FUNCTIONSTANDARD TYPE ADDITIONAL FUNCTIONS TYPE I ⇒ Dual Weighing UnitZSME200000003 ADDITIONAL FUNCTIONS TYPE II ⇒ Unit Weight Preset7 8 9 SMPL Q’TY PST 4 5 6 UNIT U.W W.T. PST CountingCounting COMBINATION TYPE ⇒ Dual Weighing Units + Preset Piece Weight Stores7 8 9 SMPL Q’TY PST 4 5 6 UNIT U.W W.T. PST This is a dual function key which selectsLow Power Warning 1-3 POWER SOURCESApplicable Power Sources Power Consumption2-3 DISPLAY BACKLIGHT 2-1 SWITCH SCALE ON2-2 SWITCH SCALE OFF CHAPTER 2 OPERATION2-4 SAMPLING SPEED & BACK TO ZERO SETTING 2-6 ZERO FUNCTION 2-5 AUTO CALIBRATIONSMPL 2-7 UNIT WEIGHT CALIBRATIONï ð 2-8-1 The Unit Weight of Object is Unknown2-8-2 The Unit Weight of Object is Known 2-8 COUNTING2-9 DEDUCTION OF CONTAINER WEIGHT 2-9-1 The Weight of Container is Unknown Tare2-9-2 Clear Tare Value 2-9-3 The Weight Container is Known Pre-set Tare 2-9-4 Clear The Pretare Value CountingZSME200000003 2-10-1 Quantity totalising 2-10 TOTALISING2-10-3 Weight Totalising 2-10-4 Recall Weight Total2-10-2 Recall Quantity Totalised ZSME200000003 2-10-5 Clear all Totalised ValuesNOTE All totals will be lost if the scale is switched off CountingCHAPTER 3 USER INTERFACE SETTING KEY ACTION3-2 PRE-SET TARE 3-3 PRE-SET QUANTITY CONDITIONS OPERATION0 = M+ will be operate when the weight is stable 3-6 MULTIPLE UAGE KEY U.W.PST / kg/lb FUNCTION SELECTION 3-5 M+ CONTINUOUS OPERATION Only After Return to Zerothe scale CountingZSME200000003 0 = Press M+ to transmit 1 = Continuous transmission 3-7 BAUD RATE SETTING for only with the serial interfaceTransmit mode 2 = Transmit only when weight is stable 3 = For EZ-2 printer4-1-1 Quantity Preset CHAPTER 4 KEYBOARD TYPES4-1 STANDARD TYPE 4-2-2 Quantity Preset 4-2 TYPE I ⇒ DUAL WEIGHING UNIT4-2-1 Unit Selection Q’TY PST 4-2-3 Weight PresetSet the Hi Limit value for unit Weight Clear the Hi Limit unit weight and quantity values4-3-1 Unit Weight Preset Stores 4-3 TYPE II ⇒ UNIT WEIGHT PRESETSMPL 4-3-2 Quantity PresetHi Limit Value for Quantity Preset Q’TY PSTQ’TY PST 4-3-3 Weight PresetSet the Hi Limit value for unit Weight Clear the Hi Limit unit weight and quantity valuesSMPL 4-4 COMBINATION TYPE ⇒ DUAL WEIGHING UNIT + UNIT WEIGHT PRESETQ’TY 4-4-1 Unit Selection4-4-2 Unit Weight Preset Stores Set Unit Weight PresetRecall the Unit Weight Preset SMPL 4-4-3 Quantity PresetSet the Hi Limit Value for Quantity Preset Q’TY PSTQ’TY PST 4-4-4 Weight PresetSet the Hi Limit value for unit Weight Clear the Hi Limit unit weight and quantity values5-1 TOTALISING CHAPTER 5 INTERFACEUse the number keys 0 or 1 key to select 0 or 5-2 PRESET TARE OPERATION CONDITIONS5-3 QUANTITY PRESET OPERATION CONDITIONS Use the number keys0 or 1 to select 0 or Use the number keys 0 or 1 to select 0 or 5-4 TOTALISING OPERATION CONDITIONS5-5 THE CONDITION TO ALLOW THE NEXT TOTALISING OPERATION 5-6 COMBINATION KEY OPERATION MODE 0 ⇒ 1 ⇒ 2 ⇒ 3 ⇒ 5-7 BAUD RATE SETTING5-8 TRANSMIT MODE SELECTION Counting NO.⇒No. of totalising operations N/W⇒Net Weight U/W⇒Unit WeightPCS⇒Piece T/N⇒Total no. of totalising operations T/W⇒Total Weight T/A⇒Total Amount