Manuals / Exmark / Household Appliance / Vacuum Cleaner

Exmark 312, 000 & higher manual Safety, 116-6363, 116-4308, PTO Switch Symbols, 116-4465

Models: 0 312 000 & higher

1 52

Download 52 pages 61.7 Kb

Page 13

Image 13

Safety

116-6363

1. Rotate the drive release 2. Push the machine. knob to loosen, slide the

knob, and tighten.

116-4308

1. Latch	2. Unlatch

PTO Switch Symbols

1. PTO–disengage	2. PTO–engage

		116-4465
1.	Fast	3.	Choke-on
2.	Slow	4.	Choke-off

Page 13

Image 13

Exmark 312, 000 & higher manual Safety, 116-6363, 116-4308, PTO Switch Symbols, 116-4465

Contents

For Serial Nos 312,000,000 & Higher PIONEER S-SERIESPart No. 4501-000Rev. A CALIFORNIA Proposition 65 Warning Model No Serial No IntroductionContents Safety Alert Symbol SafetySafety Safe Operating PracticesSafety DANGERDANGER Slope Operation OperationSafety Maintenance and Storage Using the Rollover Protection System ROPSSafety DANGERAlways shield eyes and face from battery SafetyDANGER DANGERHydraulic fluid escaping under pressure can penetrate skin and cause injury. Fluid accidentally injected into the skin must be surgically removed within a few hours by a doctor familiar with this form of injury or gangrene may result SafetySafety Safety and Instructional Decals107-2102 Safety109-6014 PTO Switch Symbols Safety116-6363 116-4308109-6016 Safety116-4430 2.Time intervalSpecifications SpecificationsSafety Interlock System Model NumbersHydrostatic Ground Drive System SeatTires & Wheels Cutting DeckOverall Width DimensionsOverall Length Overall HeightProduct Overview Curb WeightTorque Requirements Product OverviewOperation Ignition SwitchControls OperationDrive Wheel Release Valves Hour MeterFuel Shut-OffValve OperationPre-Start PTO Engagement SwitchDeck Lift Pedal Transport LockRaise the Rollover Protection System ROPS Operating InstructionsOpen the Fuel Shut-OffValve OperationEngaging the PTO Starting the EngineDisengaging the PTO Stopping the EngineDriving Forward OperationDriving in Reverse Adjusting the Anti-ScalpRollers Adjusting the Cutting HeightOperation Transporting a Unit TransportingLoading a Unit OperationRecommended Maintenance Schedules MaintenanceMaintenance Check Battery Charge Periodic MaintenanceRecommended Jump Starting Procedure Service Interval Before each use or dailyMaintenance Check Mower BladesService Interval Before each use or daily DANGERMaintenance Check Safety Interlock SystemService Interval Before each use or daily Service Interval After the first 5 hours Service Air CleanerCheck Rollover Protections Systems Roll Bar Knobs Check Seat BeltCheck Hydraulic Oil Level Service Interval Every 50 hoursLubricate Grease Fittings Check Tire PressuresService Interval After the first 100 hours Service Interval Every 200 hoursCheck Spark Plugs Change Fuel FilterMaintenance Check Spark Arrester if equippedService Interval Every 50 hours Thread Locking Adhesives AdjustmentsCopper-Based Anti-seize Dielectric GreaseMaintenance Adjusting the Blade SlopeBlade Slope Service Interval Every 500 hours Adjusting the Parking BrakePump Drive Belt Tension Deck Belt TensionFull Forward Tracking Adjustment Motion Control Handle AdjustmentMaintenance Adjusting the heightMaintenance Motion Control Linkage AdjustmentMaintenance Adjusting the Seat Ride SuspensionRemoving the Shim F.Perform the following safety check MaintenanceClean Engine and Exhaust System Area CleaningRemove Engine Shrouds and Clean Cooling Fins Clean Hydro Fan Cooling FinsMaintenance Battery DisposalDANGER Troubleshooting TroubleshootingProblem TroubleshootingEngine loses power Possible CauseSchematics SchematicsElectrical Diagram Schematics Electrical Logic Schematic2 Year Limited Commercial Warranty Pioneer S-SeriesTurf Equipment4 Year or 500 Hours Limited Consumer Warranty General Warranty Conditions and Products CoveredService Done By Service RecordDate Description of Work DonePage This page may be copied for personal use OUT-FRONTRIDING ACCESSORIES AND OPTIONS MID-MOUNTRIDING ACCESSORIES AND OPTIONSWALK-BEHINDACCESSORIES AND OPTIONS