Maintenance

 

Figure 26

 

 

Figure 27

 

44 Inch Deck

1.

Leveling adjust locking

3.

Deck hanger

1. Blades side to side

2. Measure here

 

 

nuts

 

 

2.

Deck lift arm

4.

Chain

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7.Set anti-scalp rollers to top holes or remove completely for this adjustment.

8.Set the height-of-cut lever to the 3 inch (76 mm) position. Place two “B” thick blocks (see Block Height and Rake Table) under the rear edge of the cutting deck skirt; one on each side of the cutting deck. Place two “A” thick blocks under each side of the front edge of the deck, but not under the anti-scalp roller brackets.

Block Height and Rake Table

Deck

Front Block

Rear Block

Rake “R”

Size

Height “A”

Height “B”

 

44

2.69 inches

2.99 inches

1/8–3/8 inch

 

(6.8 cm)

(7.6 cm)

(3.2–9.5 mm)

48, 52,

2.77 inches

2.81 inches

1/16–5/16 inch

& 60

(7.0 cm)

(7.1 cm)

(1.6–7.9 mm)

9.Carefully rotate the blades side to side (Figure 25 and Figure 26).

10.Loosen the leveling adjust locking nuts (item 1 Figure 27) on all four corners so that the deck is sitting securely on all four blocks. Make sure that the slack is removed from the deck hangers and the deck lift foot lever is pushed back against the stop, then tighten the four leveling adjust locking nuts.

11.Recheck that blocks fit just snugly under the deck skirt. Make sure all attachment bolts are tight

12.Continue leveling the deck by checking the front-to-rear blade slope; refer to Adjusting the

Blade Slope.

13.Recheck blades for levelness and repeat deck leveling procedure if necessary.

Adjusting the Blade Slope

1.Check the front-to-rear blade level any time you install the mower. If the front blade tip is not “R” (see Block Height and Rake Table in Deck Leveling) lower than the rear blade tip, adjust the blade level using the following instructions:

2.Park the machine on a level surface and disengage the blade control switch.

3.Move the motion control levers outward to the neutral position, engage the parking brake, stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

4.Check the air pressure of all four tires. If needed, adjust to the recommended inflation; refer to Checking the Tire Pressure in Drive System Maintenance section.

5.Check and adjust the side-to-side blade level if you have not checked the setting; refer to Deck Leveling.

6.Set the height-of-cut lever to the 3 inch (76 mm) position. Place two “B” thick blocks (see Block Height and Rake Table in Deck Leveling) under the rear edge of the cutting deck skirt; one on

36

Page 35 Page 37
Page 36
Image 36
Exmark 000 & higher, 312 manual Adjusting the Blade Slope, Inch Deck
Page 35 Page 37

0, 312, 000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.
Top Page Image Contents