Troubleshooting
Problem |
| Possible Cause |
| Corrective Action |
|
|
|
|
|
Engine loses power | 1. | Engine load is excessive | 1. | Reduce the ground speed. |
| 2. | Air cleaner is dirty. | 2. | Clean or replace the air cleaner element. |
| 3. | Oil level in the crankcase is low. | 3. | Add oil to the crankcase. |
| 4. | Cooling fins and air passages for the | 4. | Remove the obstructions from the cooling |
|
| engine are plugged. |
| fins and air passages. |
| 5. | Dirt in fuel filter. | 5. | Replace the fuel filter. |
| 6. | Dirt, water, or stale fuel is in the fuel | 6. | Contact an Authorized Service Dealer. |
|
| system. |
|
|
|
|
|
|
|
Mower pulls left or right (with levers fully | 1. | Tire pressure in drive tires not correct. | 1. | Adjust tire pressure in the drive tires. |
forward) |
|
|
|
|
|
|
|
|
|
Machine does not drive | 1. | Drive wheel system not in “operating” | 1. | Position drive wheel system in “operating” |
|
| position. |
| position; see Drive Wheel Release |
|
|
|
| Valves section in Operation. |
| 2. | Drive or pump belt is worn, loose or | 2. | Change the belt. |
|
| broken. |
|
|
| 3. | Drive or pump belt is off a pulley. | 3. | Change the belt. |
| 4. | Broken or missing idler spring. | 4. | Replace the spring. |
| 5. | Hydraulic fluid level is low or too hot. | 5. | Add hydraulic fluid to reservoir or let it |
|
|
|
| cool down. |
|
|
|
|
|
Uneven cutting height. | 1. | Blade(s) not sharp. | 1. | Sharpen the blade(s). |
| 2. | Cutting blade(s) is/are bent. | 2. | Install new cutting blade(s). |
| 3. | Mower deck is not level. | 3. | Level mower deck from |
|
|
|
| |
| 4. | Underside of mower is dirty. | 4. | Clean the underside of the mower. |
| 5. | Tire pressure in drive tires not correct. | 5. | Adjust tire pressure in the drive tires. |
| 6. | Blade spindle bent. | 6. | Contact an Authorized Service Dealer. |
| 7. | Tips of adjacent blades are at an uneven | 7. | Replace blades, spindles and (or) check |
|
| cutting height. Blades tips should be even |
| for damage to mower deck. |
|
| within 3/16 inch which is approximately |
|
|
|
| one blade thickness. |
|
|
|
|
|
|
|
Abnormal vibration | 1. | Cutting blade(s) is/are bent or unbalanced. | 1. | Install new cutting blade(s). |
| 2. | Blade mounting bolt is loose. | 2. | Tighten the blade mounting bolt. |
| 3. | Engine mounting bolts are loose. | 3. | Tighten the engine mounting bolts. |
| 4. | Loose engine pulley, idler pulley, or blade | 4. | Tighten the appropriate pulley. |
|
| pulley. |
|
|
| 5. | Engine pulley is damaged. | 5. | Contact an Authorized Service Dealer. |
| 6. | Blade spindle is bent. | 6. | Contact an Authorized Service Dealer. |
|
|
|
|
|
Blades do not rotate. | 1. | Deck belt is worn, loose or broken. | 1. | Install new deck belt. |
| 2. | Deck belt is off pulley. | 2. | Install belt on clutch and deck pulleys, |
|
|
|
| idlers, and tensioning idler per routing |
|
|
|
| decal on deck. |
| 3. | Broken or missing idler spring. | 3. | Replace the spring. |
| 4. | Deck belt not routed correctly. | 4. | Refer to belt routing decal on deck. |
|
|
|
|
|
44
