Manuals / Exmark / Lawn and Garden / Lawn Mower

Exmark 920 manual This page may be copied for personal use

Models: 0 920

1 60

Download 60 pages 43.2 Kb

Page 59

Image 59

Figure 31

This page may be copied for personal use.

1.The maximum slope you can safely operate the machine on is 15 degrees. Use the slope indicator to determine the degree of slope of hills before operating. Do Not operate this machine on a slope greater than 15 degrees. Fold along the appropriate line to match the recommended slope.

2.Align this edge with a vertical surface, a tree, building, fence pole, etc.

3.Example of how to compare slope with folded edge.

Page 59

Image 59

Exmark 920 manual This page may be copied for personal use

Contents

For Serial Nos 920,000 & Higher Lazer Z LZD Units LAZER Z D-SERIESAll Rights Reserved CALIFORNIA Proposition 65 WarningModel No Serial No IntroductionContents ALERT! YOUR SAFETY IS INVOLVED SafetySafety Alert Symbol SafetyKeep face away from nozzle and gas tank/container opening DANGEROperation Avoid prolonged breathing of vaporsDo Not mow near drop-offs or near water Do Not mow slopes when grass is wetSlope Operation Keep hands, feet, hair, jewelry, or clothing away from rotating partsDo Not wear seat belt when the roll bar is down Using the Rollover Protection System ROPSMaintenance and Storage Lower the roll bar only when absolutely necessarySafety Keep sparks, flames, or cigarettes away from batteryVentilate when charging or using battery in an enclosed space Do Not swallow electrolyteSafety Use cardboard or paper, not your hands, to find hydraulic leaksSafety Safety and Instructional DecalsSafety Safety Safety 2. PTO-disengage Safety1. PTO-engage Slow SafetyFast NeutralModel Numbers SpecificationsSpecifications Safety Interlock SystemCutting Deck SeatHydrostatic Ground Drive System Tires & WheelsOverall Width DimensionsCurb Weight Torque RequirementsOperation Product OverviewOperation ControlsHour Meter Ignition SwitchTracking Adjustment Knob Brake LeverPre-Start PTO Engagement SwitchCoolant Temperature Gauge Glow Plug Switch and LightRaise the Rollover Protection System ROPS Important Lower the roll bar only when absolutely necessaryOperating Instructions Biodiesel ReadyImportant Operator must be in seat before the PTO can be engaged Engaging the PTODisengaging the PTO Stopping the EngineSlow the machine down before making sharp turns Adjusting the Cutting HeightUse caution when making turns Driving the MachineOperation Adjusting the Anti-Scalp RollersLoading a Unit Use extreme caution when operating a unit on a rampTransporting Transporting a UnitMaintenance MaintenanceRecommended Maintenance Schedules Service Interval Monthly Periodic MaintenanceCheck Battery Charge Service Interval Before each use or dailyBatteries contain acid and produce explosive gases Recommended Jump Starting ProcedureService Interval As required Do Not jump start a weak battery if these conditions existService Interval Before each use or daily Check Mower BladesMaintenance SERVICE DEALER Check Safety Interlock SystemCheck Rollover Protections Systems Roll Bar Pins Service Air CleanerCheck Hydraulic Oil Level Service Interval After the first 5 hoursService Interval Every 40 hours Change Engine OilMaintenance Note See chart for service intervalsCheck Condition Of Belts Lubricate Grease FittingsLubricate Caster Wheel Hubs Wheel Hub - Slotted Nut Torque SpecificationService Interval After the first 100 hours Every 500 hours thereafter Service Interval Every 160 hoursLubricate Motion Control Bronze Bushings Service Interval Every 200 hoursService Interval After the first 250 hours Every 250 hours/Yearly if using Mobil 1 15W50Do Not swallow Keep out of reach of children and pets Check Engine Coolant LevelChange Engine Coolant Engine coolant is toxic. Swallowing coolant can cause poisoningThread Locking Adhesives Service Interval Every 50 hoursDo Not refuel or run engine unless spark arrester is installed Check Spark Arrester if equippedDielectric Grease AdjustmentsMobil HTS Grease Or Food-Grade Anti-seize Copper-Based Anti-seizeMaintenance Mule Drive Belt Tension AdjustmentPump Drive Belt Tension Deck Belt TensionMaintenance Belt Guide AdjustmentBrake Link Adjustment Alternator Belt TensionMaintenance Electric Clutch AdjustmentBrake Adjustment Removing the ShimG011733 Reverse Indicator AdjustmentMaintenance Maintenance Motion Control Linkage AdjustmentMaintenance Motion Control Damper AdjustmentCaster Pivot Bearings Pre-Load Adjustment because of the jumper wire being used. RunClean all debris from inside of pump drive belt compartment daily CleaningClean Engine Cooling System Clean Engine and Exhaust System AreaClean all debris from engine and exhaust system area Clean Debris From MachineClean Grass Build-Up Under Deck Clean the RadiatorDo Not swallow electrolyte Battery DisposalMaintenance DANGERTroubleshooting TroubleshootingCorrective Action TroubleshootingProblem Possible CausePossible Cause TroubleshootingProblem necessary. Install drive belt and check beltElectrical Diagram SchematicsSchematics Schematics Electrical SchematicOwner’s Responsibilities Exmark Commercial Turf Equipment2 Year Limited Warranty Instructions for Obtaining Warranty ServicePage Page Description of Work Done Service RecordService Done By DatePage This page may be copied for personal use WALK-BEHIND ACCESSORIES AND OPTIONS SEE EXMARK’S COMPLETE LINE OF ACCESSORIES AND OPTIONSMID-MOUNT RIDING ACCESSORIES AND OPTIONS OUT-FRONT RIDING ACCESSORIES AND OPTIONS