Extron electronic manual Power Supply Replacement Instructions for the MLS 304/306/406

Models: MLS 304 306 406

1 2
Download 2 pages 19.49 Kb
Page 1
Image 1
Power Supply Replacement Instructions

Plug the PCB’s power output cable to the power supply’s 2-pin power input connector.

Plug the output cable from fhe

power supply to 1.Disconnect the power cord from the switcher. the PCB’s power

input connector.

Install standoffs (2).

Install screws (2).

10. Connect the switcher’s power output cable to the power supply’s 2-pin power input connector. See the previous illustration.

11. Connect power output cable from the power supply to the switcher’s power input connector. See the previous illustration.

12. Install the insulator and attaching screws that were removed in step 7.

Position insulator under the heat sink.

Fasten the insulator to the standoffs.

Heat Sink

CThe insulator must be tucked under the heat sink to protect components from possible damage.

13. Replace the top cover and reinstall the 14 screws removed in step 3.

Power Supply Replacement Instructions

for the MLS 304/306/406

1.Disconnect the power cord from the switcher.

2.

If the switcher is rack mounted, remove it from the rack.

3.

Remove the 14 screws (8 on the top and 3 on each side) that secure the

 

switcher’s top cover, as shown below.

Lift cover straight up.

Remove (14) screws from top and sides.

4. Lift the cover straight up and off.

5. Disconnect both power supply cables, as shown below. Disconnect the two- pin power input cable from the power supply. Disconnect the power supply output cable from the switcher’s main PCB board (not the power supply).

Remove the screw.

Remove the screw.

 

 

 

 

 

Disconnect the

 

 

 

 

 

cable from the

 

 

 

 

 

main board

 

 

 

 

Disconnect the

 

 

 

 

end.

 

 

 

 

cable from the

 

 

 

 

 

power supply’s

 

 

 

 

 

2-pin connector.

 

 

 

 

Remove the

 

 

 

 

Remove the screw.

 

 

 

screw.

Power Supply to be Removed

 

6.

Remove the four screws that secure the power supply to the base of the

 

switcher. Retain at least two of the screws for installation of the new power

 

supply.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

68-1262-04

 

 

 

Extron Electronics, USA

 

Extron Electronics, Europe

 

Extron Electronics, Asia

 

Extron Electronics, Japan

Rev. A

 

 

 

 

 

 

 

 

 

1230 South Lewis Street

 

Beeldschermweg 6C

 

135 Joo Seng Rd. #04-01

 

Kyodo Building, 16 Ichibancho

09 07

 

 

 

Anaheim, CA

92805

 

3821 AH Amersfoort, The Netherlands

 

PM Industrial Bldg., Singapore 368363

 

Chiyoda-ku, Tokyo 102-0082

 

 

 

 

800.633.9876

714.491.1500

 

+800.3987.6673

+31.33.453.4040

 

+800.7339.8766

+65.6383.4400

 

Japan

 

www.extron.com

 

FAX 714.491.1517

 

FAX +31.33.453.4050

 

FAX +65.6383.4664

 

+81.3.3511.7655 FAX +81.3.3511.7656

 

 

 

 

Page 1
Image 1
Extron electronic manual Power Supply Replacement Instructions for the MLS 304/306/406