XTP T HDMI and XTP R HDMI • Setup Guide (Continued)
b. To pass bidirectional serial, infrared, or other control signals, connect a control device or a device to be |
| IR Device | |||||
| controlled to the |
| Tx/Rx | Rx Tx | G | ||
| NOTE: |
|
| Pins |
|
| |
|
|
| IR | Rx |
| ||
|
|
|
|
|
| Tx |
|
|
|
|
|
|
| G |
|
c. | Connect a host device or control LAN or WAN to the LAN | Rx |
| ||||
| Ethernet communication (see G and J on page 1). These are Ethernet | RS | Tx |
| |||
|
|
|
| ||||
| indicate link and activity status. |
|
|
|
| Tx Rx | G |
Step 4 — Connecting Outputs |
|
|
|
| |||
|
| No Ground Here |
|
|
| ||
|
|
|
|
|
|
| |
a. Connect a digital video display to the HDMI connector of the | Tip | L | Tip |
| L |
| |
| XTP R HDMI (see L on page 1). | Ring |
|
|
|
| |
| Sleeves |
| Sleeves |
|
|
| |
b. | Connect a balanced or unbalanced, stereo or mono audio | Tip | R | Tip |
| R |
|
Ring |
|
|
| ||||
| device to the 3.5 mm, |
|
| No Ground Here |
| Do not tin the wires! | |
| receiver for |
| Balanced Audio Output | Unbalanced Audio Output |
|
c.Connect an audio device to the female orange RCA connector for digital S/PDIF audio output (see N on page 1).
Step 5 — Connecting Control Devices, Relays, and Power
a.Connect a host device, such as a computer, to the female
b.Connect equipment that can be controlled via momentary or latching contact, like projector screens or lifts, to these normally open relays. Do not exceed 24 V at 1 A for each port (see O on page 1).
c.Power XTP transmitters and receivers in one of the following methods:
CONFIG
à
zz Connect the provided external power supply to the
zz Connect the provided external power supply to the
zz Connect the transmitter or receiver to an XTP matrix switcher. Enable the remote power feature on the XTP matrix switcher.
Operation
After all transmitters, receivers, and connected devices are connected and powered on, the system is fully operational. If any issues arise, verify that the cables are routed and connected properly.
NOTE: | Use the Extron XTP System Configuration Software or SIS commands to configure the transmitter or receiver (see the |
XTP T HDMI and XTP R HDMI User Guide). |
HDMI Audio Switch
On either device, move and hold the HDMI audio switch up to enable embedded audio on a display connected to the associated HDMI connector or down to disable it (for about 1 second). The switch returns to the middle position after it has been released. The associated LED lights when audio is enabled and remains unlit when audio is disabled.
Indicators
Power LED — Lights on the front and rear panel when power is applied to the device.
Transmitter indicators
Signal LED — Lights when an active TMDS clock signal is detected from the
INPUT
source. | CONFIG | SIGNAL | HDMI AUDIO | AUDIO SIGNAL CLIP |
|
| HDCP | ANALOG AUDIO | XTP T HDMI |
HDCP LED — Lights when the input signal is encrypted. |
|
|
| |
|
|
|
|
HDMI Audio LED — Lights when the HDMI input audio is selected in
Analog Audio LED — Lights when the analog audio input is selected in
Audio Signal Clip LED — Lights red when the analog audio input signal remains above
Receiver indicators
| Signal LED — Lights when an active XTP video signal is received. |
| XTP |
| AUDIO |
|
| HDCP LED — Lights when the input XTP signal is encrypted. | CONFIG | SIGNAL | HBR | BITSTREAM | LPCM |
|
|
|
|
| ||
|
|
| HDCP | HDMI | S/PDIF | ANALOG |
| HBR LED — Lights when the embedded audio signal is high bit rate audio. |
|
|
|
|
|
| Bitstream LED — Lights when the input audio signal is Dolby Digital, DTS audio format and |
|
|
| ||
| LPCM LED — Lights when the input audio signal is |
|
|
|
|
|
| HDMI LED — Lights when the input audio format is |
|
|
|
|
|
| S/PDIF LED — Lights when the input audio format is |
|
|
|
| |
| Analog LED — Lights when the input audio format is |
|
|
|
|
|
2 | © 2013 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. | www.extron.com |
XTP R HDMI