AVTrac™ Connectivity Box Installation Guide
Before installation of the AVTrac connectivity box, the base track must already |
|
be installed. For full information about AVTrac installation, consult the |
|
AVTrac Installation Guide. Install the connectivity box as follows: | Cover |
End Plate |
|
1. Remove the cover panel and end plates from the |
|
connectivity box. One end has three mounting holes | 3 Mounting Holes |
in the base, the other has two. The end with three |
|
holes faces toward the wall. Align the end with | 2 Mounting Holes |
two mounting holes with the end of the base |
|
track. | End Plate |
2. Mark where the holes in the bottom of the connectivity box lie over the base track and,
using a 1/4" metal bit (not provided), drill at least three holes through the track.
3. Using the provided masonry bit, drill 5/32" diameter by 1 1/2" deep pilot holes into the concrete through the predrilled holes in the track.
4. Reposition the connectivity box, in the correct orientation, over the
track (the end of the box with three holes must face back toward the wall). Using at least three of the provided 3/16" masonry screws, secure the box to the track and floor.
5.Populate the lid of the box with the required Architectural Adapter Plates and AC power modules. Run cabling as necessary, and reattach the end plates and cover panel.
AVTrac™ Power Module Installation Guide
Before installation of the AVTrac Power Module, the AVTrac base track and connectivity box must already be installed. For full information about AVTrac installation, consult the AVTrac Installation Guide. Install the AC module as follows:
To Main Circuit | CAll electrical installation should be |
| performed by qualified personnel in |
| accordance with local and national |
Conduit | electrical codes. |
|
US | Tabs | |
AC Power | ||
| ||
Module |
|
WSwitch off all electrical power before connecting
Junction Box | the AC conduit to a junction box, and keep power | Studs | |
off until installation is complete. | |||
|
1.
White or Blue (neutral)
Black or Brown (hot)
2. |
Green |
or Green/Yellow |
(ground) |
Install the power module at the end of the connectivity | Slots |
|
box that is closest to the wall. Slide the side tabs into the slots on the side of the connectivity box and mount the power module on the stud(s) in the floor of the box (see the figure above right). Secure the module to the stud(s) by hand tightening the provided 6/32" nut(s).
Run the unattached end of the conduit and connect it to a convenient junction or circuit box (see the figure at left). Extron recommends that the junction box be directly wired to the main circuit.
AC Conduit or Cable
From AVTrac AC Power Module
CThe module does not have a fuse and is rated at 15 A, maximum, for US modules and 10 A, maximum, for international modules.
Extron USA - West |
| Extron USA - East |
| Extron Europe |
| Extron Asia |
| Extron Japan |
| Extron China |
| Extron Middle East |
|
|
|
|
|
|
| ||||||||
Headquarters |
| +800.633.9876 |
| +800.3987.6673 |
| +800.7339.8766 |
| +81.3.3511.7655 |
| +400.883.1568 |
| +971.4.2991800 | Rev B |
|
|
|
|
|
|
| |||||||
+800.633.9876 |
| Inside USA / Canada Only |
| Inside Europe Only |
| Inside Asia Only |
| +81.3.3511.7656 FAX |
| Inside China Only |
| +971.4.2991880 FAX | 11 08 |
Inside USA / Canada Only |
| +1.919.863.1794 |
| +31.33.453.4040 |
| +65.6383.4400 |
|
|
| +86.21.3760.1568 |
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
+1.714.491.1500 |
| +1.919.863.1797 FAX |
| +31.33.453.4050 FAX |
| +65.6383.4664 FAX |
|
|
| +86.21.3760.1566 FAX |
|
|
|
+1.714.491.1517 FAX |
|
|
|
|
|
|
|
|
|
|
|
|
|
