DVI-RGB 200 Setup Guide
This guide provides instructions for an experienced installer to set up and operate Extron®
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the interface as required.
Step 2 — Connections and Initial Settings
a
bBuffered
0.4A |
|
|
| SOG ON/OFF | HIGHREFRESH |
| R | G | B | |
|
|
| BUFFERED | EDID | EDID |
|
|
| ||
|
| SOURCE |
|
|
| |||||
|
|
|
| H | V | S | ||||
|
| MONITOR |
|
| SELECT | |||||
|
|
|
|
|
| |||||
50/60 Hz |
|
|
| SELECTOR |
| LOW |
|
| OUTPUT |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
7 | 1 | 2 | 4 | 6 | 5 | 3 |
NOTE: Use only cables specifically intended for DVI interfaces. Use of
c Output connectors — Connect an RGB display to these female BNC connectors. Connect the |
| R | G | B | ||||||
|
|
|
|
|
|
|
| |||
| BNCs as shown at right for the desired RGB video format. |
|
|
|
|
| RGBHV |
|
| |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| H | V | S |
| NOTE: Ensure that the SOG DIP switch (f) is turned off (down) for RGBHV and RGBS |
|
|
|
|
| ||||
| video. |
|
|
|
|
|
|
|
|
|
| Ensure that the SOG DIP switch is turned on (up) for RGsB video. |
|
|
|
| R | G | B | ||
d EDID Source switch — |
|
|
|
|
| RGBS |
|
| ||
|
|
|
|
|
| H | V | S | ||
| Set this switch to the Monitor (up) position to connect the DDC channel between the direct |
|
|
|
| |||||
| digital video source and the local monitor. |
|
|
|
|
|
| R | G | B |
| Set this switch to the Selector (down) position to connect the DDC channel between the |
| RGsB |
|
| |||||
|
|
|
|
|
| |||||
| direct digital video source and the |
|
|
|
|
| H | V | S | |
e | EDID Select — If the EDID Source switch (d) is in the Selector (down) position, set this switch |
|
|
|
| |||||
| to the appropriate position to select the desired video resolution. Use the Refresh DIP switch |
|
|
|
| |||||
| (f) to select the refresh rate. The table at right identifies the |
|
|
|
|
|
|
|
|
|
| switch positions and the associated resolutions and vertical | EDID Select |
| Refresh | EDID Select | Refresh | ||||
| refresh rates. |
| ||||||||
|
| Switch | DIP Switch |
| Switch | DIP Switch | ||||
f | DIP switches — | Pos. Resolution | < |
| > | Pos. Resolution | < | > | ||
|
|
|
| Dwn | Up |
|
| Dwn | Up | |
| SOG (Sync on Green) On/Off switch — Set this switch to the | 0 | User EDID | EDID capture | 8 | 1366x768 | 50 Hz 60 | |||
| On (up) position to enable SOG for RGsB video. Set this switch | 1 | 800x600 | 50 | Hz | 60 | 9 | 1400x1050 50 Hz 60 | ||
| to the Off (down) position to disable SOG for RGBS or RGBHV | 2 | 1024x768 | 50 | Hz | 60 | A | 1440x900 | 50 Hz 50 | |
| video. | |||||||||
| 3 | 1280x720 | 50 | Hz | 60 | B | 1600x1200 | 50 Hz 60 | ||
| Refresh switch — | |||||||||
| 4 | 1280x768 | 50 | Hz | 60 | C | 1680x1050 | 50 Hz 50 | ||
| If the EDID Source switch (d) is in the Selector position (down) | 5 | 1280x800 | 50 | Hz | 60 | D | 1920x1080 50 Hz 60 | ||
| and the EDID select switch ( ) is in position 1 through F | 6 | 1280x1024 | 50 | Hz | 60 | E | 1920x1200 | 50 Hz 60 | |
| e | |||||||||
| position, set this switch either up or down to select the refresh | 7 | 1360x768 | 50 | Hz | 60 | F | N/A |
|
|
| rate of the selected output. See the table at right. |
|
| |||||||
|
|
|
|
|
|
|
|
|
|
If the EDID Source switch (d) is in the Selector (down) position and the EDID select switch is in position 0, set this switch up to capture the EDID data from the connected Buffered
gAC power connector — Plug a standard IEC power cord into this connector to connect the interface to a 100 to 240 VAC, 50 Hz or 60 Hz power source.
1