WebView Switches

Connecting the Switch

To connect network devices to the Switch, follow these instructions:

6.Make sure all the devices you will connect to the Switch are powered off.

7.For 10/100Mbps devices, connect a Category 5 Ethernet network cable to one of the numbered ports on the Switch. For a 1000Mbps device, connect a Category 5e Ethernet network cable to one of the numbered ports on the Switch.

8.Connect the other end to a PC or other network device.

9.Repeat steps 2 and 3 to connect additional devices.

10.If you are using the mini-GBIC port, then connect the mini-GBIC module to the mini-GBIC port. For detailed instructions, refer to the module’s documentation.

11.If you will use the Switch’s console interface to configure the Switch, then connect the supplied serial cable to the Switch’s Console port, and tighten the captive retaining screws. Connect the other end to your PC’s serial port. (This PC must be running the VT100 terminal emulation software, such as HyperTerminal.)

12.Connect the supplied power cord to the Switch’s power port, and plug the other end into an electrical outlet.

13.Power on the network devices connected to the Switch. Each active port’s corresponding Link/Act LED will light up on the Switch. If a port has an active Gigabit connection, then its corresponding Gigabit LED will also light up.

If you will use the Switch’s console interface to configure the Switch, proceed to Chapter 4: Using the

Console Interface for Configuration for directions.

If you will use the Switch’s Web-based Utility to configure the Switch, proceed to Chapter 5: Using the

Web-based Utility for Configuration.

IMPORTANT: Make sure you use the power cord that is supplied with the Switch. Use of a different power cord could damage the Switch.

Chapter 3: Connecting the Switch

NOTE: If you need to reset the Switch, unplug the power cord from the back of the Switch. Wait a few seconds and then reconnect it.

12

Connecting the Switch

Page 22
Image 22
Linksys SRW2008P, SRW2008MP manual Console Interface for Configuration for directions

SRW2008MP, SRW2008, SRW2008P specifications

The Linksys SRW2008P, SRW2008, and SRW2008MP are robust Layer 2 managed switches designed to meet the demands of small to medium-sized businesses looking for reliable networking solutions. These switches offer a range of features tailored to enhance network performance and security, making them ideal for both simple and complex networking environments.

The SRW2008P is notable for its Power over Ethernet (PoE) capabilities, enabling it to deliver power and data to PoE-compatible devices such as IP cameras and VoIP phones over a single Ethernet cable. This feature simplifies cabling requirements by reducing the need for separate power outlets, thereby streamlining installation and reducing clutter. With eight 10/100 Mbps Ethernet ports, the SRW2008P can cater to multiple devices, providing flexible connectivity options.

In contrast, the SRW2008 model focuses on delivering advanced layer 2 switching features without PoE functionality. It also boasts eight 10/100 Mbps ports and offers a comprehensive set of management features that include VLAN support, port mirroring, and Quality of Service (QoS) prioritization. These capabilities are essential for creating efficient and well-organized networks, allowing administrators to segment traffic and prioritize important data streams, which is crucial for maintaining optimal network performance.

The SRW2008MP model combines the features of the SRW2008 and SRW2008P with enhanced managed capabilities. It includes more advanced management features, allowing for greater control over traffic and network performance. The SRW2008MP supports both Layer 2 and Layer 3 capabilities, making it suitable for businesses looking to implement more sophisticated routing and switching protocols. With support for static routing, businesses can optimize their network traffic and improve overall efficiency.

All three models employ advanced technologies such as Spanning Tree Protocol (STP) and Link Aggregation Control Protocol (LACP), which enhance network resilience and bandwidth utilization. Furthermore, they come equipped with user-friendly web-based interfaces for easy configuration and monitoring, ensuring that network administration is straightforward.

In summary, the Linksys SRW2008P, SRW2008, and SRW2008MP switches deliver a combination of performance, reliability, and advanced management features ideal for small to medium-sized enterprises. Their PoE capabilities, robust VLAN support, and user-friendly interfaces make them versatile solutions for businesses seeking to enhance their network infrastructure.