Setup Guide — DVI DL 201 Tx/Rx (cont’d)
d. Press and release the EDID “Store” button (see the figure at right). The | EDID | |
rear panel LED turns amber while the EDID information is read and | STORE | |
stored from the local monitor. Afterwards, the LED turns green. | ||
|
e.Power off and disconnect the display from the transmitter.
f.Connect the transmitter to the receiver.
g.Connect a source device to the transmitter.
h.Connect a display device to the receiver and, if required, a local monitor to the transmitter.
i.Power on the display device(s), the transmitter, and the receiver.
j.Power on the source device.
Option 2 — To use the default EDID (2560x1600 @ 60 Hz):
a.Configure the DDC switches as shown in the figure at right.
b.Connect a source device to the transmitter.
c.Connect a display device to the receiver and, if required, a local monitor to the transmitter.
d.Connect the transmitter and receiver.
e.Power on the transmitter, receiver, and display devices.
f.Power on the source device.
Option 3 — To use DDC
a.Configure the DDC switches as shown in the figure at right.
b.Connect a source device to the transmitter.
c.Connect a display device to the receiver and, if required, a local monitor to the transmitter.
d.Connect the transmitter and receiver.
e.Power on the transmitter, receiver, and local monitor.
f.Power on the source device.
g.Power on the display device.
| EDID MINDER | DEFAULT EDID | REMOTE DDC |
ON ON |
|
| |
OFF | 1 | 2 | 3 |
|
|
| |
| EDID MINDER | DEFAULT EDID | REMOTE DDC |
ON ON |
|
| |
OFF | 1 | 2 | 3 |
|
|
| |
Option 4 — To use DDC
a.Configure the DDC switches as shown in the figure at right.
b.Connect a source device to the transmitter.
c.Connect a display device to the receiver and, if required, a local monitor to the transmitter.
d.Connect the transmitter and receiver.
e.Power on the transmitter, receiver, and display devices.
f.Power on the source device.
| EDID MINDER | DEFAULT EDID | REMOTE DDC |
ON ON |
|
| |
OFF | 1 | 2 | 3 |
|
|
| |
Troubleshooting
For complete instructions, consult the User’s Manual, which is available at the Extron website. If problems are encountered, verify that the cables are routed and connected properly.
If the problems persist, contact the Extron Service Department.
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500 +1.714.491.1517 FAX
Extron USA - East | Extron Europe | Extron Asia | Extron Japan |
+800.633.9876 | +800.3987.6673 | +800.7339.8766 | +81.3.3511.7655 |
Inside USA / Canada Only | Inside Europe Only | Inside Asia Only | +81.3.3511.7656 FAX |
+1.919.863.1794 | +31.33.453.4040 | +65.6383.4400 |
|
+1.919.863.1797 FAX | +31.33.453.4050 FAX | +65.6383.4664 FAX |
|
© 2010 Extron Electronics. All rights reserved.
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568 +86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800 +971.4.2991880 FAX
Rev. A
01 10
