Extron electronic IPI 201, IPI204 setup guide 68-1170-51, Rev B

IPI 200 Series Setup Guide (Continued)

Installation

Before installing your IPI 200, read the following publications, which can be found on the Extron Web site (www.extron. com):

•IPI 100 Series and IPI 200 Series User’s Manual

•IP Intercom System Frequently Asked Questions

CAUTION: Installation and service must be performed by authorized personnel only. These products must be used with UL approved grounded electrical boxes.

Speaker Microphone On LED

Microphone

	Power
PUSH TO CALL	Contact
	Relay
	Audio Out

POWER

CNO RELAY

AUDIO OUT LAN Port

LAN

	AAP Mounting
Config Port Push To Call Buttons	Screws (4)

Extron IPI 204 AAP Intercom (front panel)

IPI 204 AAP, IPI 201 AAP (rear panel)

The front panel of the IPI 204 is shown above, at left. The front panel for the IPI 201 is similar but has only one button. The rear panels for both units are identical and are shown above, at right.

1.Determine which rooms will have IP Intercoms and HelpDesk PCs, and where in each room they will be located. Ensure there is a network connection for each intercom and each HelpDesk PC.

2.Connect the LAN port to the local network, using a standard network cable, with an RJ-45 connector.

3. Connect power, and, if required, contact relay and local audio output, using the rear panel captive screw connectors (see figure at right).

4.	Test the equipment is working correctly before installing in the wall.
5.	Mount each IPI 200 into furniture, an AAP wallplate, mounting bracket for 2-gang	POWER
	wallplates, or device faceplate. The AAP versions must be secured by attaching a clamp
	bracket to the back of the intercom after it has been inserted through the front of the AAP plate.

CNO RELAY

AUDIO OUT

6.Ensure the HelpDesk PC(s) is connected to the network and power it on.

7.Install the Extron IP Intercom HelpDesk software from the disk supplied. It is also available for download from the Extron Web site (www.extron.com)

8.Use the IP Intercom HelpDesk software to configure parameters such as speaker level for all intercom units in the system. Full instructions can be found in the IPI 100 Series and IPI 200 Series User’s Manual and also in the help file for the software.

When the front panel button(s) light a low amber color, the unit is correctly installed and configured. If the button(s) light red the unit is not correctly configured and you should check the IPI 100 Series and IPI 200 Series User’s Manual or the help file for the software.

Extron USA - West	Extron USA - East	Extron Europe	Extron Asia	Extron Japan	Extron China	Extron Middle East
Headquarters
+800.633.9876	+800.633.9876	+800.3987.6673	+800.7339.8766	+81.3.3511.7655	+400.833.1568	+971.4.2991800	68-1170-51
Inside USA/Canada Only	Inside USA/Canada Only	Inside Europe Only	Inside Asia Only	+81.3.3511.7656 FAX	Inside China Only	+971.4.2991880 FAX
+1.714.491.1500	+1.919.863.1794	+31.33.453.4040	+65.6383.4400		+86.21.3760.1568		Rev B
+1.714.491.1517 FAX	+1.919.863.1797 FAX	+31.33.453.4050 FAX	+65.6383.4664 FAX		+86.21.3760.1566 FAX		06 10

© 2010 Extron Electronics. All Rights Reserved. www.extron.com