Extron electronic Quick Start Guide IPL M PDP-ES, Removing the Pioneer communication ES card

Quick Start Guide — IPL M PDP-ES

This Quick Start will briefly walk you through the installation and initial operation of the IPL M PDP-ES card in conjunction with your Pioneer plasma. For more detailed instructions, please refer to the IPL M PDP-ES User’s Manual.

Installation of the IPL M PDP-ES

Quick Start Guide — IPL M PDP-ES, cont’d Quick Start Guide — IPL M PDP-ES, cont’d

Removing the Pioneer communication ES card

Before installing the Extron IPL M PDP-ES interface card, the Pioneer communication ES card shipped within the plasma must be removed. The communication ES card is found in the communication ES card slot of the connection panel, as shown in the plasma below.

Pioneer Plasma Display

Connection Panel Pioneer ES Card Slot (communication)

Figure 1 — Pioneer ES Card Slots

To remove the Pioneer communication ES card, do the following:

1.	Ensure that the Pioneer plasma is turned off and
	disconnected from the power source.
2.	If the plasma display is laid with its screen side facing
	down, ensure that it is on a flat surface with a blanket or
	other soft material underneath.
		Never rest the plasma in such a way that weight or pressure
CAUTION
		is placed on the screen surface.
3.	If the plasma display stand obscures the communication ES
	card slot, remove or slide the stand away from the working
	area.

4.Remove the two side screws keeping the Pioneer communication ES card in place, and gently pull the center knob to remove the card.

Gently pull the center knob

Figure 2 — Removing the Pioneer ES card

Installing the Extron IPL M PDP-ES card

To install the Extron IPL M PDP-ES interface card, do the following:

1.Insert the IPL M PDP-ES gently and evenly in alignment with the two rails visible inside the ES card slot. Press on the center of the card faceplate to push the card securely into the slot.

Push gently

Figure 3 — Inserting the IPL M PDP-ES card into the communication slot

CAUTION	Be very careful when inserting the card. Do not use excessive
	force, and push the card in as straight as possible; a crooked
	entry could damage the card or the plasma.

2.When the card is seated securely in the slot, use the spring loaded thumb screws on either end of the card faceplate to secure the card in place.

Thumb screws

Figure 4 — Securing the IPL M PDP-ES

3.Affix the Extron IPL M PDP-ES sticker label over the existing Pioneer label, as shown on the following page.

Insure that the sticker is placed flush over the Pioneer label.

Figure 5 — The IPL M PDP-ES sticker label

Establishing a Hardware Connection Through the Ethernet/LAN Port

This type of connection is used to connect the IPL M PDP-ES interface card to a LAN for remote control of the Pioneer plasma and other connected devices.

1.Plug one end of a Cat 5, straight-through Ethernet cable into the LAN port of the IPL M PDP-ES interface card.

2.Plug the other end of the Ethernet cable into a network switch, hub, or router connected to an Ethernet LAN or to the Internet.

3.Ensure that your PC is connected to the network switch, hub, or router.

Configuring the IPL M PDP-ES Using the ARP Command

Both your computer and the IPL M PDP-ES interface card must be connected to the same LAN. Also, ensure that your PC is on the same subnet mask as the IPL M PDP-ES card. Use ARP to configure the IP address as follows:

1.Obtain a valid IP address for your IPL M PDP-ES card from your network administrator.

2.Obtain the IPL M PDP-ES card’s MAC address (UID #) from the label on its face panel.

3.Access the MS-DOS command prompt, then execute the ‘arp –s’ command.

Enter the desired new IP address and the MAC address (on the face panel) for the interface card. For example:

arp –s 10.13.170.15 00-05-A6-00-0A-90

4.Execute a ‘ping’ command by typing your new IP address at the command prompt. For example:

ping 10.13.170.15

1 IPL M PDP-ES • Quick Start IPL M PDP-ES • Quick Start 2 IPL M PDP-ES • Quick Start 3