Installation and Operation
Description
The P/2 DA2 Plus, P/2 DA4 Plus, and P/2 DA6 Plus are distribution amplifiers that accept video input from a
Examples of typical installations are shown in the diagrams on the following pages.
Installation
1.Power off the computer and its local monitor.
2.For optional rack mounting (four and six output only), mount the unit on one side of a 19" 1U Universal Rack Shelf (Extron part
#
a.If feet were previously installed on the bottom of the case, remove them.
b.Mount the unit on the rack shelf, as shown below, using two
Use 2 mounting holes on opposite corners.
Installation and Operation, cont’d
5.Connect an LCD panel, a
6.Connect power to the distribution amplifier.
7.Power on the local monitor, the computer, and display device(s).
P/2 DA6 Plus
0.9A | OUTPUTS |
|
|
| OUTPUTS | ||
|
| 2 |
| INPUT | VIDEO | 4 | 6 |
|
|
| GAIN | ||||
|
|
|
|
| 1V |
| P/2 DA2 Plus |
|
|
|
|
|
|
| |
50/60 Hz |
| 1 | (LOCAL MONITOR) | CPU | .7 V | 3 | 5 |
|
| ||||||
|
|
|
| P/2 DA4 Plus |
|
| |
0.9A | OUTPUTS |
|
| OUTPUTS |
| ||
|
| 2 |
| INPUT | VIDEO |
|
|
|
|
| GAIN | 4 |
| ||
|
|
|
|
| 1V |
|
|
50/60 Hz |
| 1 | (LOCAL MONITOR) | CPU | .7 V | 3 |
|
|
|
|
Indicators and Controls
Power LED: Located on the front and rear panels of the P/2 DA4 Plus and P/2 DA6 Plus only. When illuminated, it indicates that the distribution amplifier is receiving power.
Video Gain toggle switch: (P/2 DA4 Plus and P/2 DA6 Plus only) The Video Gain switch is normally set to 0.7V (down). For installations with long output cable runs, the 1.0V (up) position will give a brighter picture.
Operation
Specifications
Extron
P/2 DA2 Plus
Up to 250' w/ Extron
VGA Extension Cable
PC Computer | Projector |
Specifications
Video
Gain |
|
P/2 DA2 Plus | Unity |
P/2 DA4/DA6 Plus | 0.7V or 1.0V, switchable |
Bandwidth |
|
P/2 DA2 Plus | 270 MHz |
P/2 DA4/DA6 Plus | 300 MHz |
False front panel uses 2 front holes.
Rack Mounting
After the distribution amplifier and its connected devices are powered up, the system is fully operational. If any problems are encountered, verify that the cables are routed and connected properly. For units with the Video Gain toggle switch, verify that the switch position is correct (refer to the previous Indicators and Controls section).
Optional VGA Cables and Adapters
Video input
Number/signal type | 1 |
Connectors |
|
P/2 DA2 Plus | 1 |
P/2 DA4/DA6 Plus | 1 |
| are available) |
(2)
3.Connect the computer’s VGA output to the input of the distribution amplifier (P/2 DA2 Plus cable or the center connector of the P/2 DA4 Plus or P/2 DA6 Plus). See rear panel diagrams on next page.
4.Connect the computer’s monitor to the “Local Monitor” output of the distribution amplifier.
•6', 15', 25', 50', 75', 100', 150', 200' and 250'
•
•
•
Nominal level | 0.7V |
Minimum/maximum levels | Analog |
P/2 DA2 Plus | 0.4V to 1.4V |
P/2 DA4/DA6 Plus | 0.3V to 1.5V |
Impedance | 75 ohms |
Horizontal frequency | 15 kHz to 135 kHz |
Vertical frequency |
|
P/2 DA2 Plus | 30 Hz to 150 Hz |
P/2 DA4/DA6 Plus | 30 Hz to 170 Hz |
1 | P/2 DA 2/4/6 Plus • Installation and Operation | P/2 DA 2/4/6 Plus • Installation and Operation | 2 | P/2 DA 2/4/6 Plus • Specifications | 3 |