Extron electronic P/2 DA2XI specifications

User’s Guide

P/2 DA2xi and P/2 DA2xi MT • InstallationP/2 DA2xi and P/2 DA2xi MT • Installation

Introduction

32

Extron Electronics, USA

1230 South Lewis Street

Anaheim, CA 92805

USA

714.491.1500

Fax 714.491.1517

Extron Electronics, Europe

Beeldschermweg 6C

3821 AH Amersfoort

The Netherlands

+31.33.453.4040

Fax +31.33.453.4050

Extron Electronics, Asia

135 Joo Seng Road, #04-01

PM Industrial Building

Singapore 368363

+65.6383.4400

Fax +65.6383.4664

Extron Electronics, Japan

Daisan DMJ Building 6F

3-9-1 Kudan Minami

Chiyoda-ku, Tokyo 102-0074 Japan

+81.3.3511.7655

Fax +81.3.3511.7656

www.extron.com

Distribution Amplifiers

68-713-01 Rev. C

Printed in the USA

06 03

P/2 DA2xi

P/2 DA2xi MT

The P/2 DA2xi and the P/2 DA2xi MT are distribution amplifiers

that accept video input from a VGA, XGA, or UXGA compatible

PC and distribute the signal to separately buffered outputs. Each

output can be extended with Extron VGA Mini-HR cables from 6'

to 250' in length. The MT model also has audio input and output.

Both models can be powered by newer computers compatible

with the new VESA standard using pin 9 of the VGA connector as

the +5VDC source. An external power supply is also provided

for use with older computers, where power is unavailable

through the VGA connector or the available power is inadequate.

Features

• Powered by computer — This unit can be powered by most

newer computers.

• Power/Signal LED — Green LED = power + signal. Amber

LED = power but no signal. Off = no power.

• Gain/Peak DIP switch — To compensate for longer cable runs.

• Out Imp DIP switch — Changes the output impedance to be

compatible with all projectors.

• Cable retention chain — To prevent a lost or misplaced input

VGA cable, the cable can be secured to the unit (either model)

with the supplied chain (attached to the right standoff nut of

the input VGA connector).

Figure 1 — P/2 DA2xi MT with chain

Installation

The P/2 DA2xi and P/2 DA2xi MT can be mounted on a rack

shelf, under a desk or tabletop, or on a projector bracket.

Rack mounting

For optional rack mounting, mount the P/2 DA2xi or P/2 DA2xi

MT on a VersaTools 19" 1U Rack Shelf (part #60-190-20) or a

standard Universal 1U Rack Shelf (part #60-190-01) as shown in

figure 2.

Only products in the VersaTools line can be mounted to a

VersaTools rack shelf.

Figure 2 — Mounting the P/2 DA2xi or P/2 DA2xi MT on

a rack shelf

1. Remove the rubber feet (if installed) and mount the unit on the

rack shelf, using two screws in opposite (diagonal) corners.

2. Install blank panel(s) or other unit(s) to the rack shelf.

3. Insert the shelf into the rack, and secure the shelf to the rack

using the supplied machine screws.

Furniture or projector mounting

Furniture mount or projector mount the unit using the mounting

kit (part #70-077-01, furniture [optional with the P/2 DA2xi,

standard with P/2 DA2xi MT] or #70-077-04, projector [optional

with both units]) as follows:

1. Attach the mounting brackets to the P/2 DA2xi or

P/2 DA2xi MT with the provided machine screws (figure 3).

Figure 3 — Desk and projector mounting

FCC Class A Notice

Note: This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference, in which case the user will be required to correct the interference at his

own expense.

Note: This unit was tested with shielded cables on the peripheral devices. Shielded

cables must be used with the unit to ensure compliance.

General

Power ................................................ +5VDC from pin 9 of the VGA input of a PC

that complies with VESA DCC version 3

Or .......................................... 100VAC to 240VAC, 50/60 Hz, 5 watt,

external, autoswitchable; to 12VDC, 1A

power supply. P/2 DA2xi and P/2 DA2xi MT

require 0.2A.

Temperature/humidity ................. Storage -40° to +158°F (-40° to +70°C) / 10%

to 90%, non-condensing

Operating +32° to +122°F (0° to +50°C) / 10%

to 90%, non-condensing

Rack mount ...................................... Yes, with optional 1U VersaTools rack shelf,

part #60-190-20 or Universal rack shelf, part

#60-190-01

Enclosure type ................................. Metal

Enclosure dimensions .................... 1" H x 4.3" W x 3" D

2.5 cm H x 10.9 cm W x 7.6 cm D

(Depth excludes connectors.)

Product weight ................................ 0.5 lbs (0.3 kg)

Shipping weight .............................. 3 lbs (1.4 kg)

Vibration ........................................... ISTA/NSTA 1A in carton (International Safe

Transit Association)

Listings .............................................. UL, CUL

Compliances .................................... CE, FCC Class A, VCCI, AS/NZS, ICES

MTBF ................................................. 30,000 hours

Warranty ........................................... 3 years parts and labor

Specifications are subject to change without notice.

MONITOR

AUDIO

INPUT

Use 2 mounting holes on

opposite corners.

VersaTools Rack Shelf

1/4 Rack Width False Front

Face Plate

Universal Rack Shelf

DISTRIBUTION AMPLIFIER

DISTRIBUTION AMPLIFIERDISTRIBUTION AMPLIFIER

DISTRIBUTION AMPLIFIER

MDA SERIES

DISTRIBUTION AMPLIFIER

Ceiling

Digital Projector

Projector

Mounting

Bracket

Mounting

Bolt

INPUTMONITOR

P/2 DA2xi

OUTPUT

GAIN/

PEAK

SPARE

EXT POWER (see manual)

0.1A MAX