CUSTOMIZING YOUR RANGEHOOD
The front strip of the rangehood can be customized by replac- ing the factory supplied strip with a custom front strip made from the same materials as your cabinets. The front strip is attached to the rangehood by three recessed screws and three key hole slots on the back side of the strip as indicated in FIGURE 15. It is necessary only to remove the three lower screws to remove the front strip. The top screws will slide out of the key holes once the three lower screws are removed.
Side View of the Rangehood
Rangehood Body
Front
Strip
Three Screws
FIGURE 15
The front strip dimensions are given in FIGURE 16. For a custom front strip, a local cabinet shop can make a strip to match your cabinets. If you wish to keep the frame of the front panel and only replace the glass panel, the dimensions follow: Height = 5 11/16", Depth = 1/8", Width = 29 11/16" (for 30" model) 35 11/16" (for 36" model) 23 5/8" (for 24" model).
5 7/8"
23 5/8" or 29 15/16" or 35 15/16" 13/16"
FIGURE 16
WIRING DIAGRAM
•This rangehood uses Flourescent Lamp Type
USE AND CARE INFORMATION
This rangehood system is designed to remove smoke, cooking vapors and odors from the cooktop area.
For Best Results
Start the rangehood several minutes before cooking to develop proper airflow. Allow the unit to operate for several minutes after cooking is complete to clear all smoke and odors from the kitchen.
Rangehood Control Panel
All controls are located under the front panel and are shown in FIGURE 17.
Light On/Off Switch ( L )
On/Off switch for the fluorescent light. Moving the switch to the
1 Position turns the light On. Moving the switch to the 0 Position | ||
turns the light Off. |
| |
Blower On/Off |
| |
Switch ( M ) |
| |
On/Off switch for the |
| |
blower. Moving the |
| |
switch to the 1 Posi- |
| |
tion turns the blower |
| |
On. Movingtheswitch |
| |
to the 0 Position turns | FIGURE 17 | |
the blower Off. | ||
| ||
Blower Speed Switch ( S )
Controls blower speed. Moving the switch to the 1 Position turns the blower on LOW. Moving the switch to the 2 Position turns the blower on MEDIUM. Moving the switch to the 3 Position turns the blower on HIGH.
Operation Indicator Light ( I )
Red light will be on when the rangehood is operating.
Microswitch ( MS )
When the front panel of the rangehood is closed, the rangehood will turn off by a microswitch. This turns the rangehood On and Off without adjusting the switches for the Light or Blower and it remembers the last speed setting.
Cleaning
The metal grease filters should be cleaned frequently in hot deter- gent solution or placed in the dishwasher. Clean exterior surfaces with hot soapy water. Using abrasives and scouring agents can scratch rangehood finishes and should not be used to clean finished surfaces.
Replacing the Fluorescent Light
To replace the fluorescent light, remove the retainer clips from both ends of the glass diffuser as indicated in FIGURE 18. Carefully slide the glass diffuser all the way to the left. Lower the right end of the glass below the support flange, then remove the glass by sliding it back to the left. Replace the diffuser glass by reversing these directions.
FIGURE 18
WARRANTY & SERVICE
All Faber products are warranteed against any defect in materials or workmanship for the original purchaser for a period of 1 year from the date of original purchase. This warranty covers labor and replace- ment parts. The warranty does not cover consumable parts such as filters and light bulbs. This warranty does not apply if this product has been subjected to faulty installation, misuse, or neglect. This warranty excludes any consequential expense or damage resulting from any use or malfunction of the product. All implied warranties are limited to the duration of this warranty.
To obtain warranty service, contact the dealer from whom you pur- chased the rangehood, or the local Faber distributor. If you cannot identify a local Faber distributor, contact us at (508)
Version 10/05 - Page 7
