PREPARE THE CABINET

1.Disconnect and move freestanding range from cabinet opening to provide easier access to upper cabinet and rear wall. Put a thick, protective covering over cooktops, set-in ranges or countertops to protect from damage or dirt.

2.Determine and clearly mark with a pencil the center line of the cabinet on the wall and on the underside of the cabinet where the rangehood will be installed.

3.Determine the proper cutouts for the ductwork. Make all necessary cuts in the walls or cabinets for the ductwork. Install the ductwork before mounting the rangehood.

4.If the cabinet bottom is recessed, wood filler strips need to be installed.

5.Drill four 3/16" clearance holes for hood mounting screws.

8.Remove the grease filters.

9.Remove the terminal box cover (located on the back wall of the hood. Remove the power supply cable knockout using a flat-blade screwdriver. Attach strain relief in power supply cable opening so that clamping screws are inside of rangehood.

10.Attach damper to exhaust opening on top of the range- hood using the two small screws from the hardware pack- age.

INSTALL THE RANGEHOOD

1.

Place the rangehood mounting screws close to the holes

in the cabinet bottom.

2.

Lift rangehood into place while feeding wiring through

strain relief.

3.

Insert the screws through the clearance holes and start

CENTERLINE

WALL

v

 

WOOD lLLER STRIPSE

CLEARANCER

RECESSEDECABINETD

HOLES

BOTTOMSTONLY

FIGURE 6

 

v

v

v

them into the rangehood.

4.

Connect the vent system to the rangehood and seal all

joints with duct tape.

5.

Connect the Power Supply Cable to the rangehood.

Attach the White lead of the power supply to the White lead

of the rangehood with a twist-on type wire connector. Attach

the Black lead of the power supply to the Black lead of the

rangehood with a twist-on type wire connector. Connect the

Green ( Green and Yellow ) ground wire under the Green

grounding screw.

6.

Replace the grease filters.

6. Cut a 6 1/2" diameter hole in cabinet bottom as shown.

CENTERLINE

v DIAMETER HOLE

WALL

v

FIGURE 7

7.Determine and make the proper cutout for the Power Supply Cable. Use a 1 1/4" Drill Bit to make this hole. Run the Power Supply Cable through the wall or cabinet. DO NOT turn on the power until installation is complete. Use caulking to seal around the wire opening.

FIGURE 8

7.

Turn the power supply on. Turn on blower and lights. If

the rangehood does not operate, check that the circuit breaker

is not tripped or the house fuse blown. If the unit still does

not operate, disconnect the power supply and check that the

wiring connections have been made properly.

Version 04/08 - Page 6

Page 6
Image 6
Faber Cabinet Rangehood installation instructions Prepare the Cabinet, Install the Rangehood

Cabinet Rangehood specifications

The Faber Cabinet Rangehood represents a significant advancement in kitchen ventilation technology, seamlessly integrating into modern cabinetry. This appliance is designed not only for its functionality but also for its aesthetic appeal, making it an ideal choice for contemporary kitchens.

One of the standout features of the Faber Cabinet Rangehood is its powerful suction capability. Equipped with high-performance motors, these range hoods are capable of efficiently removing smoke, steam, and odors from the kitchen, ensuring a fresh cooking environment. The rangehood operates at various speeds, allowing users to select the appropriate level of ventilation based on the intensity of cooking.

Another key characteristic of the Faber Cabinet Rangehood is its discreet design. It is engineered to fit snugly within kitchen cabinetry, ensuring that it does not disrupt the overall design of the kitchen. This allows homeowners to maintain a clean and streamlined look while still benefiting from effective ventilation.

Additionally, Faber incorporates advanced technology into their rangehoods. Many models are equipped with sensor controls that automatically adjust the fan speed based on the level of cooking emissions detected. This smart technology not only enhances user convenience but also optimizes energy consumption by minimizing unnecessary power use.

Faber also offers a range of noise-reduction innovations in their cabinet rangehoods. These models operate quietly, allowing for a peaceful cooking experience without the distraction of loud fan noises. This is particularly beneficial in open-concept living spaces where kitchen sounds may affect adjoining areas.

Easy maintenance is another advantage of the Faber Cabinet Rangehood. Many of these range hoods feature dishwasher-safe filters, making it simple to keep the unit clean and functioning efficiently over time. Some models also come with LED lighting, which not only illuminates the cooking surface but provides energy-efficient brightness, enhancing the overall cooking experience.

In summary, the Faber Cabinet Rangehood combines aesthetic elegance with powerful performance. Its high suction capabilities, smart technology, discreet integration into cabinetry, and user-friendly maintenance features make it a smart choice for anyone looking to elevate their kitchen. With a Faber range hood, homeowners can enjoy an effective ventilation solution while maintaining the stylish look of their kitchens.