- 2 - | UK |
Instructions for fitting pebbles
This model is provided with a pebble fuel effect, which is packed separately in the carton. To fit follow the instructions given below.
The front panel will need to be removed in order to change the fuel bed.
Warning - The front panel should only be taken off once the fire has been fully secured to the wall.
This should only be done when the appliance is switched off.
Warning - Take care handling the front panel as it can be easily damaged.
a. Remove the two screws which hold the front panel in place - see Fig. 9.
b. While holding the front by its sides with both hands carefully tilt forwards - see Fig. 9.
c. Then lift up and out - see Fig. 9
Place the front panel flat on a protective surface such as a matt with the glass facing away from the floor.
Remove the (4) screws securing the log effect - see Fig. 10.
Lift the log effect up and out, taking care not to damage the logs as they are fragile.
Fit the flat bed fuel effect ensuring that the bracket to the rear on the fuel effect slots in between the fuel effect retaining bracket and the rear glass - see ‘x’ in Fig. 11.
Remove the pebbles from the packaging and arrange on the fuel bed.
Refit the front panel ensuring that its base is held in place i.e. that it slots into the channel on the frame, reversing the steps as outlined previously.
Lamp Replacement
WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE REMOVING LAMPS.
Warning - The lamps reach high temperatures during operation. For this reason, allow the lamps to cool down after switching off the appliance.
The front panel will need to be removed in order to change lamps.
Warning - Take care handling the front panel as it can be easily damaged.
a. Remove the two screws which hold the front panel in place - see Fig. 9.
b. While holding the front by its sides with both hands carefully tilt forwards - see Fig. 9.
c. Then lift up and out - see Fig. 9
Place the front panel flat on a protective surface such as a matt with the glass facing away from the floor.
Remove the (4) screws securing the log effect - see Fig. 10. Lift the log effect up and out, taking care not to damage the logs as they are fragile.
Remove the (2) screws securing the hinged cover - see Fig. 10. Tilt the hinged cover (see ‘b’ in Fig. 11).
Remove the defective lamp by unscrewing it as shown in Fig. 12. Replace with a 60W E14 SES Clear Candle bulb. Take care not to over- tighten the lamp.
Steps for reassembling the heater
Refit the fuel effect ensuring that the bracket to the rear on the fuel effect slots in between the fuel effect retaining bracket and the rear glass - see ‘x’ in Fig. 11.
Refit the front panel ensuring that its base is held in place i.e. that it slots into the channel on the frame, reversing the steps as outlined previously.
Thermal Safety Cut-out
For your safety, this appliance has been fitted with thermal
To bring the heat back into operation, remove the cause of the overheating, then unplug or turn off the electrical supply to the heater for up to 10 minutes.
When the heater has cooled sufficiently,
Caution: In order to avoid a hazard due to inadvertent resetting of the thermal
Recycling
For electrical products sold within the European Community.
At the end of the electrical products useful life it should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local
Authority or retailer for recycling advice in your country.
Cleaning
WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE HEATER.
For general cleaning use a soft clean duster – never use abrasive cleaners. The glass viewing screen should be cleaned carefully with a soft cloth. DO NOT use proprietary glass cleaners.
After Sales Service
Should you require after sales service or should you need to purchase any spares, please contact the retailer from whom the appliance was purchased or contact the service number relevant to your country on the warranty card.
Please do not return a faulty product to us in the first instance as this may result in loss or damage and delay in providing you with a satisfactory service.
Please retain your receipt as proof of purchase.