- 1 - | UK |
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLYAND RETAINED FOR FUTURE REFERENCE
Important Safety Advice:
When using electrical appliances, basic precautions should be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:
If the appliance is damaged, check immediately with the supplier before installation and operation.
Do not use this heater in the immediate surroundings of a bath, shower or swimming pool.
Do not use outdoors.
This heater must not be located immediately above or below a fixed socket outlet or connection box.
Do not cover or obstruct in any way the heat outlet grille located underneath the heater. Overheating will result if the heater is accidentally covered.
In the event of a fault unplug the heater.
Unplug the heater when not required for long periods.
The supply cord must be placed on the right hand side of the heater away from the heat outlet underneath the heater.
Although this heater complies with safety standards, we do not recommend its use on deep pile carpets or on long hair type of rugs.
This appliance is not intended for use by children or other persons without assistance or supervision if their physical, sensory or mental capabilities prevent them from using it safely. Children should be supervised to ensure that they do not play with the appliance.
The appliance must be positioned so that the plug is accessible.
If the supply cord is damaged it must be replaced by the manufacturer or service agent or similarly qualified person in order to avoid a hazard.
WARNING: IN ORDER TO AVOID OVERHEATING, DO NOT COVER THE HEATER.
The heater carries the Warning symbol, indicating that it must not be covered.
WARNING: In order to avoid a hazard due to inadvertent resetting of the thermal
on and off by the utility.
Electrical
WARNING – THIS APPLIANCE MUST BE EARTHED
This heater must be used on an AC ~ supply only and the voltage marked on the heater must correspond to the supply voltage.
Do not switch the appliance on until properly installed. Please read all the safety warnings and operating instructions.
General
Unpack the heater carefully and retain the packaging for possible future use, in the event of moving or returning the fire to your supplier.
Contents of Carton.
•Heater.
•Wall fixing bracket.
•Fixing screws and wall plugs.
•Remote control and batteries (2 AAA’s type).
•Spare bulb.
Do not connect the heater to an electricity supply until it is installed on a wall correctly. - see ‘Installation’.
A choice of 1kW or 2kW heat output is provided by the fan heater, which is concealed underneath the unit.
The heater can be used remotely or manually. - see ‘Operation’. General features of remote control are:
•Heat output can be increased or decreased according to your particular requirements.
•The illumination of fuel effect can be increased or decreased.
Please note: Used in an environment where background noise is very low, it may be possible to hear a sound which is related to the operation of the flame effect. This is normal and should not be a cause for concern.
Installation
Do not connect appliance until properly fixed to the wall and the Instruction leaflet is read fully.
The minimum distances must be observed.
For installation of the appliance, care must be taken not to damage concealed cables.
Please be careful while drilling the holes.
This model is designed to be permanently fixed to a wall at a minimum height of 300mm.
The wall bracket must be fitted horizontally and the cable routed to the bottom right of the heater as in Fig. 1.
A height of 600mm from bottom of heater to floor is recommended for optimum viewing of fuel bed (see Fig. 2 for recommended fixing dimensions).
For optimum viewing mark the top two screw fixing positions on wall in accordance with the recommended fixing dimensions - see Fig. 2.
Fix the wall bracket using the two plugs and screws provided - see Fig. 3.
Carefully lift the heater up ensuring that the top rear ledge of heater engages the wall bracket and is sitting centrally positioned. - see Fig. 4
(b).
Rotate the bottom fixing bracket down. - see Fig. 4 (c). Gently bring the heater level with the wall. - see Fig. 4 (d).
Mark the bottom hole position (see Fig. 5), remove the heater ensuring that the bottom fixing bracket is rotated up.
Drill and fit wall plug.
Refit the heater to the wall fixing bracket (i.e. follow steps as in Fig. 4 a, b, c and d) and rotate the bottom fixing bracket down again and use the screw provided to permanently fix the heater in place.
The heater should not be connected until the instruction leaflet is read fully.
Manual & Remote Operation
Setting | Operation | Setting |
Flame Effect |
| Bottom Neon |
Flame Effect & 1Kw Heat | Press the ‘ I ’ button | Middle Neon |
Flame Effect & 2Kw Heat | Press the ‘ I ’ button again | Top Neon |
The switches are located at the right hand side of the heater. The Standby switch must first be turned ‘ON’ to operate the heater manually or by remote control.
Note: It takes some time for the receiver to respond to the transmitter. DO NOT PRESS the buttons more than once within two seconds for correct operation.
To go to the previous settings press the O button.
Pressing the O button on the remote turns off the light & heat settings. To resume press the I button until the desired setting is reached - see Fig. 8.
To increase or decrease the brightness of the flames, use the dimmer button or the 
button on the Remote Control. The heat setting will remain the same.
To turn off the power the Standby Switch must be turned ‘OFF’.
