MAINTENANCE INSTRUCTIONS
OPERATING INSTRUCTIONS
Cleaning the Air Purifier
Disconnect the unit from the outlet before performing maintenance or troubleshooting.
It is recommended that you regularly clean the air intake grill and
1.Lay the unit down with face upwards.
2.Grasp both corners of the bottom of the air intake grill and pull upwards. (Fig. 8)
Fig. 8
3.Lift air intake grill gently towards top of unit, to remove.
4.To remove the HEPA filter, pull up on the tags on either side of the filter and lift upwards. (Fig. 9)
Tags
Fig. 9
5.To clean the
8.To replace the air intake grill, first attach the top of the grill and then snap in the lower part of the grill.
Replacing the HEPA Filter
The HEPA filter should last approximately six (6) to nine (9) months depending on usage and household environment. The change filter indicator will illuminate when the filter requires replacing. Disconnect the unit from the power source before performing any maintenance or troubleshooting. WARNING: Do not attempt to wash or vacuum the HEPA filter as this will cause damage to the filter.
1.Lay the unit down with face upwards.
2.Grasp both corners of bottom of the air intake grill and pull upwards. (Fig. 8)
3.To remove the HEPA filter, pull up on the tags on either side of the filter and lift upwards. (Fig. 9)
4.Remove the new HEPA filter from the bag.
5.There is a sticker located on the base and top of the HEPA filter, fill in the date that this filter was installed into the unit. This helps you keep track of when a new filter will be needed.
6.Insert the new HEPA filter into the air purifier with the arrow pointing down. (Fig. 13)
Before Using the Air Purifier
Remove all parts from packaging. Insert 2 AAA batteries into the remote control. Before use verify that the HEPA filter is in place:
1.Lay the unit down with face upwards.
2.Grasp both corners of the bottom of the air intake grill and pull upwards. (Fig. 1)
Fig. 1
3.To replace the air intake grill- insert the top of the air intake grill first and then snap in the lower part of the grill.
4.Plug the unit into an electric outlet, the unit will be ready to run.
5.Press the “On/Off” button on the display panel to turn the unit “On”.
Description of the Display Panel
Display Panel
Using the Air Purifier
1.Plug the unit into an electric outlet, the unit will be ready to run.
2.Press the “On/Off” button on the display panel to turn the unit “On”. Repress the button to turn the unit “Off”.
Fan Speed
NOTE: There will be approximately a one (1) second delay between pressing the fan speed button and the unit changing speed.
1.When the unit is turned on, the fan will automatically start at medium speed for about 3 seconds and then default to low speed. The fan speed is indicated on the control panel.
2.To change the fan speed, press the fan speed control button on the front of the unit. Each time it is depressed the fan speed changes ranging from quiet to auto. (Fig. 2)
Fan Settings: | Fig. 2 |
| |
1= Quiet | 2= Low |
3= Medium | 4= High Auto |
3.If you select the auto fan speed, the dust and odor sensors will detect the air quality in the room and will
automatically adjust the fan speed. NOTE: When the fan speed is in the “AUTO” mode, AUTO will appear at the
HEPA
Filter Frame
Fig. 10
Fig. 13
7. To replace the air intake grill, first |
attach the top of the grill and then |
snap in the lower part of the grill. |
| Control |
Display Panel | Buttons |
1. | Fan Speed Indicator |
2. | |
3. | Odor Detected in Air Indicator |
4. | Dust Detected in Air Indicator |
top right hand corner of the display panel. The fan speed will appear after the sensors select the required fan speed for the most efficient cleaning.
6.Run under tap water until water runs clear. Allow to air dry for 24 hrs before replacing onto the HEPA filter frame. (Fig. 11)
7.To clean the air intake grill, you may use a vacuum with a crevice tool to get trapped dust out from between the gaps.
Then clean with a
damp cloth to remove any extra dirt and dust. (Fig. 12)
Fig. 11
Fig. 12
8
8. To reset the clean filter indicator |
plug the unit in, turn the unit “On”, |
then press and hold the timer button |
until the clean filter indicator turns |
off. |
5. | Timer Display |
6. | Change Filter Indicator |
Control Buttons
7.Fan Speed Control Button
8.Neutralize “On/Off” Indicator
9.Neutralize “On/Off” Control Button
10.“On/Off” Power Button
11.Ionizer Control Button
12.Ionizer “On/Off” Indicator
13.Timer Control Button
5