Fantom Vacuum FM718 owner manual Cleaning the Hepa Dust Cup Filter, Cleaning the Hepa Filter Frame

Fig. 9

Fig. 10

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

Cleaning the HEPA Dust Cup Filter

IMPORTANT, Please Note : The Rinseable “TapClean” HEPA Dust Cup Filter will stop most of the tiniest dust particles and airborne allergens from re-entering the air you breathe. In fact, it stops 99.97% of all particles as small as 0.3 microns - many times smaller than a human hair!!! Because of this incredible filtration performance, the HEPA Dust Cup Filter will quickly accumulate many fine dust particles inside the white filter folds that are difficult to see but which will eventually block or reduce your suction power - if not cleaned properly. Clean the HEPA Filter after each use as described in this section.

1.To remove the HEPA

filter, remove the dust cup from the unit.

2.To remove the dust cup cover, hold the cover by the handle, turn counter clockwise and lift the cover off. (Fig. 9)

3.Remove the HEPA Rinseable "Tap Clean" filter from the dust cup. (Fig. 10)

4.Remove the filter ring that is around the HEPA filter. Vigorously "TapClean" the HEPA

dust cup filter on a hard surface until no more dust is observed falling out. (Fig. 11) The HEPA filter may also be washed by running it under the tap allowing the water

to run on the dirty side. (Fig. 12) We recommend washing it once a month or when suction appears reduced. Always allow 24 hours for air drying before replacing into the vacuum.

Fig. 11

Please Note: The white material in the HEPA filter will discolor over time - This is NORMAL and will NOT affect the performance of the filter.

Warning: Always empty the dust cup and clean the HEPA dust cup filter before each use and during prolonged usage. Never over fill the dust cup - remove dirt and clean the HEPA dust cup filter each time the dust cup is emptied during prolonged usage or risk motor damage.

Cleaning the HEPA Filter Frame

1.Before replacing the HEPA filter in the HEPA Filter frame, you can (should) rinse the frame in lukewarm water by just running it under the tap to remove any dust that is adhering to the frame. (Fig. 13) Do NOT place in dishwasher.

Fig. 13

2.Make sure that the filter frame is completely dry before replacing into the dust cup. Always air dry.

Cleaning the Filter Ring
1. Around the HEPA filter
there is a filter ring.
This is washable in
lukewarm water.
(Fig. 14) To remove
the filter ring, slide it
off the HEPA filter.
2. We recommend
washing the filter ring
when you are
washing your HEPA
filter. Always allow the
filter ring to air dry for	Fig. 14
24 hours before replacing onto

the HEPA filter. Never run the vacuum without all the filters in place.

Note: This is a washable filter, but we recommend replacing it every three (3) months.

Cleaning the Secondary Filter

1.Underneath the HEPA filter there is a secondary filter.

This is washable in lukewarm water.

(Fig. 15) We recommend washing it when you are washing your HEPA filter. Always allow the secondary filter to air dry for 24 hours before replacing into the vacuum. Never run

the vacuum without

the secondary filter in place. Fig. 15

Changing & Cleaning the Pre- Motor Filter

Warning: To reduce the risk of electric shock, the power cord must be disconnected before removing the dust cup, HEPA filter,changing the filters or performing maintenance/trouble shooting checks.

The pre-motor filter is located in the vacuum underneath the dust cup. Please note that this filter is a washable filter and can be cleaned by rinsing under lukewarm water. Always allow the pre-motor filter to air dry for 24 hours before replacing in the vacuum. Do not use a hair dryer to dry it. Air dry only. To remove the pre- motor filter:

1.Remove the dust cup. (See instructions on page 5 for removing the dust cup).

2.Hold the Pre-Motor filter cover and turn counter-clockwise to unlock and lift to remove. (Fig. 16)

3.Remove the pre-motor filter and clean by rinsing under lukewarm water.

4.After air drying for 24 hours, replace in the vacuum.

5.To replace the pre-motor filter cover, insert the locking lugs into the lug holes and turn clockwise to lock.

Pre-Motor

Filter

Cover

Fig. 16

Pre-Motor

Filter

Lug

Holes

Changing & Cleaning the Exhaust Filter

Warning: To reduce the risk of electric shock, the power cord must be disconnected before removing the dust cup, HEPA filter,changing the filters or performing maintenance/trouble shooting checks.

The exhaust filter is located on the front of the unit below where the dust cup is. To remove the exhaust filter, you must first remove the filter cover.

1.Check the exhaust filter frequently and replace with new filters when dirty.

2.Remove the exhaust filter cover. (Fig. 17)

3.Remove the exhaust filter.

4.Rinse in lukewarm water and let the filter air dry for 24 hours before re- installing into the vacuum. Do not use a washing machine to rinse the filter. Do not use a hair dryer to dry the filter. Air dry only. Never operate the vacuum without ALL the filters in place.

5.When the filter is dry, replace into the vacuum and replace the filter cover.

Note: A severely soiled or clogged filter should be thoroughly washed with fresh tepid water. A mild detergent may be used if required.

Fig. 12

Fig. 17

6

7