Fantom Vacuum FM732H Changing & Cleaning the Pre-MotorFilter, Assembling Your Vacuum Cleaner

Wash once a month or when suction appears reduced

Warning: Allow 24 hours for drying before replacing in unit.

Fig. A

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

7.Vigorously “TapClean” the HEPA Dust Cup Filter on a hard surface until no more dust is observed falling out from between the pleats of the filter. See illustration at right.

PLEASE NOTE: The white pleated filter material in the HEPA Dust Cup Filter will discolor over time -This is NORMAL and will NOT affect the performance of the filter. If the HEPA Dust Cup Filter

is properly "TapCleaned” after each use and suction does not return to 100%, then we suggest that the HEPA filter be “TapCleaned” vigorously until no more dust

can be removed, then rinsed under the faucet and allowed to air dry for 24 hours before refitting into the vacuum. (Fig. A) This should be done once a month or when suction appears to be reduced.

Important: The suction hole must be open, free of any obstructions at all times. Otherwise, the motor will overheat and could become damaged.

8.Reassemble the debris screen back onto the HEPA filter cartridge.

9.To replace the HEPA filter back into the dust cup container, hold the filter by the stem and insert it up into the dust cup container making sure that the top rim of the filter fits onto

the top of the dust cup container and twist it clockwise to lock in place.

Ensure that the filter assembly is completely seated inside the dust cup (container).

Important: Do NOT use the HEPA filter cartridge without the debris screen in place.

10.Re-install dust cup into the vacuum and re-attach hose.

Changing & Cleaning the

Pre-Motor Filter

The pre-motor filter is located underneath the dust cup container. This is a rinseable filter but should be replaced every six (6) months. Never operate the vacuum without ALL the filters in place.

•Push the Power On/Off button to the "Off" position and disconnect the power cord from the wall outlet.

•Remove the dust cup container.

•Remove the pre-motor filter and rinse in lukewarm water, let dry completely. Do not use a hair dryer to dry it. Air dry only.

•When filter is completely dry, replace pre-motor filter back into the unit and replace the dust cup container.

Assembling Your Vacuum Cleaner

Note: Always remove the power plug from the wall outlet before assembling or removing accessories.

1.Attaching the Flexible Hose into the Vacuum

Connect the flexible hose into the air intake duct. Push in until you hear a “click”, indicating it is in its locked position.

To remove the flexible hose first remove the power nozzle power cord from the receptacle for the power nozzle power cord, then depress locking button and remove hose.

Connect the hose connecting power cord from the flexible hose to the power cord receptacle that is on the unit just below the air intake duct.

Air intake duct

Power cord receptacle

2.Fitting the Telescopic Tube to the Curved Wand / Hose Extension

Push the telescopic tube into the curved wand / hose extension, as shown in the illustration below.

Make sure that the telescopic tube locks in place.

3.Extending the Telescopic Tube

Push forward on the plastic button and pull the inner tube outward.

Plastic

Button

4.Fitting the Floor to Carpet Brush to the Telescopic Tube

Push the telescopic tube into the floor brush as show in the illustration below.

Telescopic

Tube

Floor to Carpet

Nozzle

Using Power Nozzle

1.Connecting the power nozzle with the telescopic tube:

A)Depress the button on the telescopic tube and insert it into the slot on the power nozzle elbow.

B)Push the telescopic tube down until you hear a "click".

(see illustration below).

Telescopic

Tube

Power

Nozzle

2.Insert the motorized brush power cord plug into the power socket on the flexible hose. To start motorized brush press the On/Off button that is located on the motorized brush.

7

4