Assembling the Pressure Washer
OPERATING INSTRUCTIONS
Fig. 3Fig. 4 | Fig. 5 |
1 1/4”
7/8” SCREW 7/8”
SCREWSCREW
Fig. 7
Fig. 6
Fig. 2 |
|
Attaching The Wheels To The | Attaching The Handle To The |
Pressure Washer | Pressure Washer |
Attaching High Pressure Hose to Pressure Washer
Once the pressure washer is assembled, you are ready to use the unit.
1.While facing the rear of the unit attach the high pressure hose to the high pressure output connector on the back side of the unit. Twist on tight to avoid leakage. (Fig. 8)
Fig. 8
2.Then attach the other end of the high pressure hose to the high pressure hose connector on the trigger gun. (Fig. 9)
Fig. 9
3. Once the high pressure hose is |
connected to the trigger gun, you can |
attach any of the lances and |
accessories that you desire. To |
attach either of the lances or the |
brush to the trigger gun, hold the |
trigger gun in your left hand insert the |
desired lance or the brush and push |
Garden Hose Connection
Once all the desired attachments and the high pressure hose are attached to the pressure washer, you can connect the garden hose to the unit.
1.Make sure that the water intake filter is inside the water intake inlet.
(Fig. 11)
2.Attach the male adapter (supplied) to the water intake connector on the front side of the unit. (Fig. 11)
3.Attach the female hose coupling to the garden hose. (Fig. 11)
4.Connect the female hose coupling to the male adapter making sure that it is tightly secured in place. (Fig. 11)
Water inlet
Water intake
filter
Garden hose (not supplied)
Fig. 11 | Garden hose |
Hose | coupling |
connector |
|
4. After all the connections have been |
and BEFORE you plug the pressure |
washer into an electrical outlet, open |
the water supply and press on the |
trigger switch in order to remove any |
air which may be in the hose or |
pump. Continue to press on the |
trigger switch until you get a constant |
flow of water coming out of the trigger |
1.Carefully take all the parts out of the packaging container and place together on a flat, stable surface.
2.Insert the wheels onto the wheel axle and push in the wheel lock to lock the wheels in place. (Fig. 2)
3.Turn the pressure washer upside down and slide the front support onto the unit. (Fig 2)
4.Using the 1” long nickel plated screw, secure the front support to the unit.
1.Place the handle on the unit as shown in Fig. 3.
2.Push the handle in at the bottom until it is in position. See Fig. 4.
3.Let the handle slide down to its resting place as shown in Fig 5 & 6.
4.To secure the handle to the unit, screw 1 1/4” screw at the top hole and the two (2) 7/8” screws on each side of the handle. See Fig. 7.
it in all the way into the connector on |
the trigger gun and turn it clockwise |
60° until it locks in place. To remove |
the attachment, push down on the |
attachment and turn counter- |
clockwise 60° and then pull out. |
Make sure that the attachments are |
securely locked in place before use. |
(Fig. 10) |
Fig. 10
gun. Allow water to flow for 30 |
seconds. |
5. Once this is accomplished, stop |
pressing the trigger switch. Engage |
the safety lock on the trigger |
6. Ensure that the "On/Off" switch, at |
the side of the unit, is on the "Off" |
position, then plug the unit into an |
electrical outlet and turn the unit to |
the "On" position. |
7. Now you are ready to use the |
pressure washer. Disengage the |
safety lock and depress the trigger on |
the trigger gun. |
5
6
