Fantom Vacuum VPW49H Attaching High Pressure Hose to Pressure Washer, Garden Hose Connection

Assembling the Pressure Washer

OPERATING INSTRUCTIONS

Fig. 3Fig. 4 Fig. 5

1 1/4”

7/8” SCREW 7/8”

SCREWSCREW

Fig. 7

Fig. 6

Fig. 2

Attaching High Pressure Hose to Pressure Washer

Once the pressure washer is assembled, you are ready to use the unit.

1.While facing the rear of the unit attach the high pressure hose to the high pressure output connector on the back side of the unit. Twist on tight to avoid leakage. (Fig. 8)

Fig. 8

2.Then attach the other end of the high pressure hose to the high pressure hose connector on the trigger gun. (Fig. 9)

Fig. 9

3. Once the high pressure hose is

connected to the trigger gun, you can

attach any of the lances and

accessories that you desire. To

attach either of the lances or the

brush to the trigger gun, hold the

Garden Hose Connection

Once all the desired attachments and the high pressure hose are attached to the pressure washer, you can connect the garden hose to the unit.

1.Make sure that the water intake filter is inside the water intake inlet.

(Fig. 11)

2.Attach the male adapter (supplied) to the water intake connector on the front side of the unit. (Fig. 11)

3.Attach the female hose coupling to the garden hose. (Fig. 11)

4.Connect the female hose coupling to the male adapter making sure that it is tightly secured in place. (Fig. 11)

Water inlet

Water intake

filter

Garden hose (not supplied)

Fig. 11	Garden hose
Hose	coupling
connector

4. After all the connections have been

and BEFORE you plug the pressure

washer into an electrical outlet, open

the water supply and press on the

trigger switch in order to remove any

air which may be in the hose or

Attaching The Wheels To The Pressure Washer

1.Carefully take all the parts out of the packaging container and place together on a flat, stable surface.

2.Insert the wheels onto the wheel axle and push in the wheel lock to lock the wheels in place. (Fig. 2)

3.Turn the pressure washer upside down and slide the front support onto the unit. (Fig 2)

4.Using the 1” long nickel plated screw, secure the front support to the unit.

Attaching The Handle To The Pressure Washer

1.Place the handle on the unit as shown in Fig. 3.

2.Push the handle in at the bottom until it is in position. See Fig. 4.

3.Let the handle slide down to its resting place as shown in Fig 5 & 6.

4.To secure the handle to the unit, screw 1 1/4” screw at the top hole and the two (2) 7/8” screws on each side of the handle. See Fig. 7.

trigger gun in your left hand insert the

desired lance or the brush and push

it in all the way into the connector on

the trigger gun and turn it clockwise

60° until it locks in place. To remove

the attachment, push down on the

attachment and turn counter-

clockwise 60° and then pull out.

Make sure that the attachments are

securely locked in place before use.

(Fig. 10)

Fig. 10

pump. Continue to press on the

trigger switch until you get a constant

flow of water coming out of the trigger

gun. Allow water to flow for 30

seconds.

5. Once this is accomplished, stop

pressing the trigger switch. Engage

the safety lock on the trigger

6. Ensure that the "On/Off" switch, at

the side of the unit, is on the "Off"

position, then plug the unit into an

electrical outlet and turn the unit to

the "On" position.

7. Now you are ready to use the

pressure washer. Disengage the

safety lock and depress the trigger on

the trigger gun.

5

6