The ribbon doesn’t seem to wind or print properly.

Symptoms: The printer skips ribbon panels, prints ribbon panels out of the usual YMCK order (resulting in strangely colored output), or simply winds the ribbon until the printerÕs on-line LED light flashes.

¥Check that the proper ribbon type is installed according to the ribbon type option selected in QuatroÕs printer driver setup window (see Chapter 4, Section IV).

¥The Ribbon Sensor needs to be recalibrated. This is a simple procedure which may be required every so often. Refer to the following steps to recalibrate this sensor:

1.Install a Full-Color YMCKO Ribbon into the printer, and position an unused Magenta (red colored) panel across the top of the light emitting portion of the Ribbon Sensor (shown on page 9).

2.Close the Printhead Assembly securely, but leave the Top Cover open.

3.With the Top Cover open, locate the rectangular opening on the left-hand side of the printer. Just inside this opening are four small, white switches aligned vertically. The switches are labeled 1 through 4, with the top switch being number 1.

4.With the tip of a small flathead screw driver, flip Switch 1 towards the rear of the printer to turn the switch ON.

5.Disconnect the power cable from the back of the printer, and close the printerÕs Top Cover.

6.Press and hold the on-linebutton. Then, reconnect the power cable into the back of the printer while continuing to hold the on-linebutton.

7.Release your finger from the on-linebutton once either of the printerÕs LED lights turn ON. Notice that only one LED will be lit, either the on-lineor the on/cancel.

8.On the right-hand side of the printer, locate the three small holes toward the rear of the Top Cover. Through the center hole, there is a potentiometer labeled RP2 which adjusts the sensitivity of the Ribbon Sensor.

9.Gently insert the tip of a small flathead screw driver into the hole so it fits into the slot of RP2. Slightly rotate RP2 in either direction until both the on-lineand on/cancel LEDÕs turn OFF. (WARNING: RP2 cannot be rotated all the way around! It has a stopping point in each direction; DO NOT rotate RP2 beyond these points!).

Troubleshooting 37

Page 40 Page 42
Page 41
Image 41
FARGO electronic Quatro ID Card Printer manual Ribbon doesn’t seem to wind or print properly
Page 40 Page 42

Quatro ID Card Printer specifications

The FARGO Electronic Quattro ID Card Printer is a versatile and efficient solution for creating high-quality identification cards. This state-of-the-art printer is designed to cater to a variety of industries, including education, healthcare, and corporate environments, making it an ideal choice for organizations that require reliable and secure ID card printing.

One of the standout features of the Quattro ID Card Printer is its ability to produce vibrant, full-color cards with exceptional clarity. Utilizing advanced dye-sublimation technology, the printer ensures that images and text are reproduced with remarkable precision. The printer has a resolution of 300 dpi, providing sharp details and rich colors that enhance the overall appearance of the ID cards.

Another key characteristic of the Quattro printer is its dual-sided printing capability. This feature allows users to print on both sides of the card in a single pass, significantly reducing production time and enhancing productivity. Organizations can utilize the back side of the card for vital information, such as magnetic stripes, barcodes, or additional identification details.

The Quattro ID Card Printer also incorporates smart card encoding technology, which enables the printing and encoding of RFID and smart chip technology onto cards. This is particularly beneficial for organizations that require heightened security measures, as it allows for the storage of sensitive information directly on the ID card itself.

User-friendliness is another essential aspect of the FARGO Quattro ID Card Printer. The device features an intuitive interface with easy-to-navigate controls, making it accessible for operators of all skill levels. Additionally, the printer is designed for seamless integration with existing software systems, facilitating a smooth workflow.

The robust build and compact design of the Quattro printer make it suitable for a variety of settings. Its durable construction ensures longevity while occupying minimal space on a desk or workstation. Furthermore, the printer is equipped with USB and Ethernet connectivity options, providing flexibility in how it can be deployed within an organization.

In conclusion, the FARGO Electronic Quattro ID Card Printer is a powerful tool for creating secure, professional-grade identification cards. With its advanced printing technology, dual-sided printing capability, smart card encoding, and user-friendly features, it stands out as a reliable choice for organizations looking to enhance their ID card issuance processes. Whether for employee badges, student IDs, or membership cards, the Quattro printer is an excellent investment in security and quality.
Top Page Image Contents