Fender 65 Princeton manual Rear Panel, Vacuum Tubes, Specifications

Rear Panel

J.Power CORD SOCKET—Connect to a grounded A/C outlet using the supplied power cord, in accordance with the voltage and frequency ratings specified on the rear panel of your amplifier.

K.FUSE—Protects the amplifier from electrical faults. Replace a blown fuse only with the type and rating specified on the rear panel of your amplifier.

L.POWER SWITCH—Turns the amplifier ON-OFF as indicated by the front panel power jewel.

M.INTERNAL SPEAKER—Plug-in connection for the 8Ω internal speaker. A speaker must always be connected at this jack when the amplifier is ON. A speaker impedance load of 8Ω should be used to avoid distortion or damage to the amplifier. When using only the internal speaker jack, a speaker impedance load

of 8ohms (minimum) should be used to avoid distortion or damage to the amplifier.

N.EXTERNAL SPEAKER—Plug-in connection for an external speaker. This jack is wired in parallel with the INTERNAL SPEAKER JACK {M} and affects the speaker impedance load. Use 8Ω minimum total. To use the external speaker output, first disconnect the internal speaker. Then connect a 16Ω speaker load (minimum) to the internal speaker jack and another 16Ω speaker load (minimum) the external speaker jack.

O.FOOTSWITCH—Plug the (included) 2-button footswitch in here. The footswitch enables remote switching of the Reverb and Vibrato effects.

P.REVERB JACKS—RCA jacks that route signal to and from the Reverb tank.

Vacuum Tubes

Your new Fender® amplifier comes equipped with the highest quality tubes available, sourced from various manufacturers all over the world. Because of occasional irregularities in supply, the specific tube type used in each amplifier is subject to change without notice.

When replacing output tubes, please note the specific tube markings on the original tubes factory supplied with your amplifier. For example, 6L6 output tube types used by Fender include, but are not limited to: 6L6GC; 6L6WXT; 6L6C; 6L6GE; etc. The installation of a different type may require significant adjustment by a qualified technician to avoid reduction in performance and tube life.

Additionally, Groove Tubes™ sorts and tests many of our output tubes, and paints them with a color-coded label. If your amp came supplied with, for example, White-labeled

6L6WXT tubes, then a new set of White 6L6WXT tubes will be the perfect direct replacement.

If you have questions or concerns, contact your Fender dealer or authorized service center.

Model "65 Princeton® Reverb Amp"

Tube locations left to right at rear:

�	�	�
�	�	�
�	�	�
�	��	��	��	��	��	��
			��	��	��	��
			��	��	�	��

Specifications

TYPE:	PR 770
PART NUMBERS:	2172000000 (120V~, 60Hz)	2172001000 (110V~, 60Hz) TW	2172003000 (240V~, 50Hz) AUS
	2172004000 (230V~, 50Hz) UK	2172005000 (220V~, 50Hz) ARG	2172006000 (230V~, 50Hz) EUR
	2172007000 (100V~, 50/60Hz) JPN
POWER REQUIREMENT:	125W
INPUT IMPEDANCE:	1MΩ
POWER AMP OUTPUT:	15W into 8Ω @ < 10% THD, 1kHz
SPEAKERS:	One 8Ω, 10", Jensen Special Design C-10R, (P/N 0069347000)
DIMENSIONS:	Height: 16 in (40.6 cm)	Width: 19 7/8 in (50.5 cm)	Depth: 9 1/2 in (24.1 cm)
WEIGHT:	28 lb (61.6 kg)

Product specifications are subject to change without notice.

fender.com