Manuals / Ferris Industries / Lawn and Garden / Lawn Mower

Ferris Industries 5900737 IS2000ZKAV2561 CAL, 25HP, 61 CUT ZERO-TURN RIDING MOWER Fuel Filter

Models: 5900737 IS2000ZKAV2561 CAL, 25HP, 61 CUT ZERO-TURN RIDING MOWER 5900750 IS2000ZKAV2761, 27HP, 61 CUT ZERO-TURN RIDING MOWER 5901170 IS2000ZK2761, 27HP, 61 CUT ZERO-TURN RIDING MOWER 5900624 IS2000ZKAV2552, 25HP, 52 CUT ZERO-TURN RIDING MOWER 5900619 IS2000ZKAV2561, 25HP, 61 CUT ZERO-TURN RIDING MOWER 5900629 IS2000ZLKAV2661, 26HP, 61 CUT ZERO-TURN RIDING MOWER 5900714 IS2000ZKAV25/61 AUS/NZ, 25HP, 61 CUT ZERO-TURN RIDING MOWER 5900713 IS2000ZKAV25/52 AUS/NZ, 25HP, 52 CUT ZERO-TURN RIDING MOWER 5900625 IS2000ZK2752, 27HP, 52 CUT ZERO-TURN RIDING MOWER 5900738 IS2000ZBV3061 CAL, 30HP, 61 CUT ZERO-TURN RIDING MOWER 5900670 IS2000ZBV3061, 30HP, 61 CUT ZERO-TURN RIDING MOWER 5900715 IS2000ZBV30/61 AUS/NZ, 30HP, 61 CUT ZERO-TURN RIDING MOWER 5900754 IS2000ZKAV3461SS, 34HP, 61 CUT ZERO-TURN RIDING MOWER

1 52
Download 52 pages 5.31 Kb
Page 30
Image 30

Maintenance

Regular Maintenance

CHECK TIRE PRESSURES

Tire pressure should be checked periodically, and maintained at the levels shown in the chart. Note that these pressures may differ slightly from the “Max Inflation” stamped on the side-wall of the tires. The pressures shown provide proper traction, improve cut quality, and extend tire life.

Tire

Pressure

Front

25 psi (1,72 bar)

 

 

Rear

15 psi (1,03 bar)

 

 

CHECKING / ADDING FUEL

To add fuel:

1.Remove the fuel cap (see Figure 1).

2.Fill the tank to the bottom of the filler neck. This will allow for fuel expansion.

NOTE: Do not overfill. Refer to your engine manual for specific fuel recommendations.

3. Install and hand tighten the fuel cap.

FUEL FILTER

The fuel filter is located in the fuel line between fuel tank and carburetor, near the fuel pump. If filter is dirty or clogged, replace as follows:

1.Disconnect the negative battery cable.

2.Place a container below the filter to catch spilled fuel.

3.Using a pliers, open and slide hose clamps from fuel filter.

4.Remove hoses from filter.

5.Install new filter in proper flow direction in fuel line.

6.Secure with hose clamps.

7.Reconnect the negative battery cable when finished.

CHANGE OIL & FILTER

1.Warm engine by running for a few minutes. (Refer to the engine operator’s manual for oil & filter replacement instructions.)

2.Remove the oil drain hose (A, Figure 15) from the cable clamp (B) on the right-hand side of the frame and route the hose through hole in the engine deck as shown in Figure 15.

3.Place a small pan under the oil drain hose to catch the oil. Using the appropriate tools, remove the cap from the oil drain hose (A) and drain the engine oil.

4.After draining, replace the cap and wipe up any spilled oil. Reinstall the oil drain hose into the cable clamp to retain the hose during normal operation.

5.Place an absorbent shop cloth under the engine oil filter. Remove the engine oil filter and replace with a new one.

6.Remove the shop cloth and wipe up any spilled oil.

Figure 14. Checking Tire Pressure

WARNING

Gasoline is highly flammable and must be handled with care. Never fill the tank when the engine is still hot from recent operation. Do not allow open flame, smoking or matches in the area. Avoid over-filling and wipe up any spills.

Do not remove fuel filter when engine is hot, as spilled gasoline may ignite. DO NOT spread hose clamps further than necessary. Ensure clamps grip hoses firmly over filter after installation.

Do not use gasoline containing METHANOL, gasohol containing more than 10% ethanol, gasoline additives, premium gasoline, or white gas because engine/fuel system damage could result.

B

A

Figure 15. Engine Oil Drain

A.Oil Drain Hose

B.Cable Clamp

28

www.ferrisindustries.com

Page 29 Page 31
Page 30
Image 30
Ferris Industries 5900737 IS2000ZKAV2561 CAL, 25HP, 61 CUT ZERO-TURN RIDING MOWER manual Check Tire Pressures, Fuel Filter
Page 29 Page 31