Ferris Industries 5900619 IS2000ZKAV2561, 25HP, 61 CUT ZERO-TURN RIDING MOWER, 5900624 IS2000ZKAV2552, 25HP, 52 CUT ZERO-TURN RIDING MOWER, 5900625 IS2000ZK2752, 27HP, 52 CUT ZERO-TURN RIDING MOWER, 5900629 IS2000ZLKAV2661, 26HP, 61 CUT ZERO-TURN RIDING MOWER, 5900670 IS2000ZBV3061, 30HP, 61 CUT ZERO-TURN RIDING MOWER, 5900713 IS2000ZKAV25/52 AUS/NZ, 25HP, 52 CUT ZERO-TURN RIDING MOWER, 5900714 IS2000ZKAV25/61 AUS/NZ, 25HP, 61 CUT ZERO-TURN RIDING MOWER, 5900715 IS2000ZBV30/61 AUS/NZ, 30HP, 61 CUT ZERO-TURN RIDING MOWER, 5900737 IS2000ZKAV2561 CAL, 25HP, 61 CUT ZERO-TURN RIDING MOWER, 5900738 IS2000ZBV3061 CAL, 30HP, 61 CUT ZERO-TURN RIDING MOWER, 5900750 IS2000ZKAV2761, 27HP, 61 CUT ZERO-TURN RIDING MOWER, 5900754 IS2000ZKAV3461SS, 34HP, 61 CUT ZERO-TURN RIDING MOWER, 5901170 IS2000ZK2761, 27HP, 61 CUT ZERO-TURN RIDING MOWER TROUBLESHOOTING COMMON CUTTING PROBLEMS

Troubleshooting

TROUBLESHOOTING COMMON CUTTING PROBLEMS

PROBLEM CAUSE REMEDY

Streaking. 1. Blades are not shar p. 1. Shar pen your blades.

2. Blades are worn down to far. 2. Replace your blades.

3. Engine speed is too slow. 3. Always mow at full throttle.

4. Ground speed is too fast. 4. Slow down.

5. Deck is plugged with grass 5. Clean out the mower.

6. Not over lapping cutting rows 6. Overlap your cutting rows.

enough.

7. Not over lapping enough when 7. When turning your effective cutting width

turning. decreases–over lap more when tur ning.

Scalping. 1. Lawn is uneven or bumpy. 1. Roll or level the lawn.

2. Mower deck cutting height is 2. Raise the cutting height.

set too low.

3. Ground speed is too fast. 3. Slow down.

4. Deck is not leveled correctly. 4. Correctly level the deck.

5. Tire pressure is low or uneven 5. Check and inflate the tires.

Stepped Cutting. 1. Deck is not leveled correctly. 1. Level the deck correctly.

2. Tires are not properly inflated. 2. Check and inflate the tires.

3. Blades are damaged. 3. Replace the blades.

4. Deck shell is damaged. 4. Repair or replace the deck.

5. Mower spindle is bent or loose. 5. Repair or replace the spindle.

6. Blades are installed incorrectly. 6. Reinstall the blades correctly.

Uneven Cutting. 1. Deck is not leveled correctly. 1. Level the deck correctly.

2. Blades are dull or worn. 2. Shar pen or replace the blades.

3. Blades are damaged. 3. Replace the blades.

4. Deck is clogged with grass 4. Clean out the deck.

clippings.

5. Deck shell is damaged. 5. Repair or replace the deck.

6. Mower spindle is bent or loose. 6. Repair or replace the spindle.

7. Blades are installed incorrectly. 7. Reinstall the blades correctly.

8. Tires are not properly inflated. 8. Check and inflate the tires.

Stingers. 1. Blades are not sharp or nicked. 1. Shar pen your blades.

2. Blades are worn down too far. 2. Replace your blades.

3. Engine speed is too slow. 3. Always mow at full throttle.

4. Ground speed is too fast. 4. Slow down.

5. Deck is plugged with grass. 5. Clean out the mower.

Troubleshooting, Adjustment & Service