First Alert FA168C-CN, FA168CP Phone System Select, Report Format, Dynamic Signaling Priority

NOTE: Entry of a number other than one specified will give unpredictable results.

For fields *43-*46:Enter 0–9; #+11 for B; #+12 for C; #+13 for D; #+14 for E; #+15 for F. Enter[✱] as the fourth digit if a 3-digit account number (for 3+1 dialer

reporting format) is used. Enter 0 as the first digit of a 4-digit account number for Nos. 0000-0999. Exit field by pressing ✱ (and press next field number) if only 3

digits are used. E.g., For Acct. B234 , enter:

#+11 2 3 4

✱43 PARTITION 1 PRIMARY SUBS. ACCT. No.

	See box above for entries. To clear entries
[FFFF]
	from field, press	*43 *.

✱44 PARTITION 1 SECONDARY SUBS. ACCT. No.

✱45 PARTITION 2 PRIMARY SUBS. ACCT. No.

✱46 PARTITION 2 SECONDARY SUBS. ACCT. No.

[FFFF]

[FFFF]

[FFFF]

See box above for entries. To clear entries from field, press *44*.

See box above for entries. To clear entries from field, press *45 *.

See box above for entries. To clear entries from field, press *46 *.

✱47 PHONE SYSTEM SELECT

[1]	If Cent. StaIS. NOT	on a WATS line:
	0=Pulse Dial; 1=Tone Dial;
	if Cent. Sta.IS on	a WATS line:
	2 = Pulse Dial ; 3 = Tone Dial

✱48 REPORT FORMAT

primary

✱49 SPLIT/DUAL REPORTING

✱50 15 SEC DIALER DELAY (BURG)

✱53 SESCOA/RADIONICS SELECT

✱54 DYNAMIC SIGNALING DELAY

secondary

[0]

[0]

[0]

[0]

[70]0 = 3+1, 4+1 ADEMCO L/S STANDARD

1 = 3+1, 4+1 RADIONICS STANDARD

2 = 4+2 ADEMCO L/S STANDARD

3 = 4+2 RADIONICS STANDARD

6 = 4+2 ADEMCO EXPRESS

7 = ADEMCO CONTACT ID® REPORTING

8 = 3+1, 4+1 ADEMCO L/S EXPANDED

9 = 3+1, 4+1 RADIONICS EXPANDED

0	= Disable (Backup report only)
		Primary Phone No.			Second
Phone No.
1	= Alarms, Restore, Cancel			Others
2	= All except Open/Close, Test			Open/Close,	Test
3	= Alarms, Restore, Cancel			All
4 = All except Open/Close, Test				All
5	= All				All
0			; 1 = yes
	= no UL: must be “0”

0= Radionics (0-9, B-F)

1= SESCOA (0-9 only reporting) Select “0” for all other formats.

Delay selectable from 0 to 225 secs in 15-sec increments.

0 = no delay (both signals sent), 1 = 15 secs, 2 = 30 secs, etc. UL: must be “0”

✱55 DYNAMIC SIGNALING PRIORITY

[0]	0 = Primary Dialer first; 1 = Long Range Radio
	first.

TO PROGRAM SYSTEM STATUS, & RESTORE REPORT CODES (								✱59 – ✱76, & ✱89):
For 3+1 or 4+1 Standard Format:			Enter a code in the			firstbox: 1–9, #+10 for 0, #+11 for B, #+12 for C, #+13 for D, #+14 for E, #+15 for F.
A 0 (	not	#+10) in the firstbox will disable a report. A 0 (				not #+10) in the second		box will result in automatic advance to the next field.
For Expanded or 4+2 Format:			Enter codes in	both	boxes (1st and 2nd digits) for 1–9, 0, or B–F, as described above.
A 0 (	not	#+10) in the second	box will eliminate the expanded message for that report. A 0 (					not #+10) in both boxes will disable the report.
For Ademco Contact ID® Reporting:			Enter any digit (other than 0) in the				firstbox, to enable zone to report (entries in the		second	boxes are ignored).
A 0 (	not	#+10) in the firstbox disables the report.				UL: see installation instructions for requirements

SYSTEM STATUS REPORT CODES (		✱59– ✱ 68)
✱59	EXIT ERROR REPORT CODE
✱60	TROUBLE REPORT CODE
✱61	BYPASS REPORT CODE
✱62	AC LOSS REPORT CODE
✱63	LOW BAT REPORT CODE
✱64	TEST REPORT CODE
✱65	OPEN REPORT CODE

[0]See box above.

[00]	See box above.
[00]	See box above.
[00]	See box above.
[00]	See box above.
[00]	See box above. Use Scheduling mode to set periodic test reports.
	[0,0,0]	See box above.

Part. 1 Part. 2 Common

✱66 ARM AWAY/STAY RPT CODE

Away Stay

Part. 1

[0,0,0,0,0,0] See box above.

Away Stay	Away Stay
Part. 2	Common

– 4 –