1 SAFETY AND WARNINGS

2

 

WARNING!

Electrical shock hazard

Before carrying out any work on the electrical section of the appliance, it must be disconnected from the mains electricity supply.

Connection to a good earth wiring system is absolutely essential and mandatory.

Alterations to the domestic wiring system must only be made by a qualified electrician.

Failure to follow this advice may result in electrical shock or death.

WARNING!

Cut hazard

Take care - some panel edges are sharp.

Failure to use caution could result in injury or cuts.

IMPORTANT SAFETY INSTRUCTIONS!

Particular attention shall be given to the relevant requirements regarding ventilation. Read these instructions carefully before installing this product.

Please make this information available to the person installing the appliance as it could reduce your installation costs.

This appliance is to be installed and serviced only by an authorised person.

Installation must comply with your local building and local gas authority codes and electricity regulations.

Incorrect installation, for which the manufacturer accepts no responsibility, may cause personal injury or damage and could invalidate any warranty or liability claims.

These appliances are registered in: (New Zealand) at www.energysafety.govt.nz and (Australia) with SAI Global at www.saiglobal.com.

This gas appliance is suitable for connection only to the gas type for which it was set at the factory, as declared on the appliance data label. It is not convertible for use on any other gas type. If in doubt, refer to the local gas network operator or gas supplier to confirm gas type at installation site. Do not modify this appliance.

Do not use or store flammable materials on or near this appliance.

Do not spray aerosols in the vicinity of this appliance while it is in operation.

Packing elements (eg plastic bags, polystyrene foam, staples, packing straps etc) and tools should not be left around during and after installation, especially if they are within easy reach of children, as these may cause serious injuries.

You must remove the transit screws before installing the cooktop. See step 8 of installation instructions.

Before you install the appliance, please make sure that

the local distribution conditions (nature of gas and pressure) and the adjustment of the appliance are compatible. For adjustment conditions for this appliance see ‘Gas rate summary’.

a suitable disconnection switch is incorporated in the permanent wiring, mounted and positioned to comply with the local wiring rules and regulations. A means of disconnection with at least a 3 mm air gap contact separation in all poles must be incorporated into the fixed wiring in accordance with the wiring rules, unless the local wiring rules allow for alternative means.

the appliance is connected to a 220V - 240V 50Hz (10 A) power supply only and earthed via the power supply cable.

there is a power outlet within reach of the power supply cable (900 mm from the centre rear of the product). This must be accessible after installation. The power supply cable should not touch any metal parts.

if the power supply cable is damaged, it is replaced only by the special cable: Part no. 534050 - Flex Terminal Block Assy NZ/AU, obtainable from authorised Fisher & Paykel Service Agents.

the supply connection point (gas shut-off valve) is accessible after installation. the benchtop is made of a heat resistant material.

the installation complies with all the requirements of Australian and New Zealand Gas Installation Standards (AS/NZS 5601.1.2010), including that the product has to be installed so that the surface temperature of any nearby combustible surface will not exceed 65 OC above ambient. See step 5 ‘Clearance Dimensions’.

When you install the appliance

We do not recommend you flush mount or seal this appliance into the bench with silicone or glue. Doing so will make future servicing difficult. Fisher & Paykel will not be liable for any costs associated with removing or replacing a sealed-in appliance, nor for repairing any damage that may be incurred by doing this.

If installed with an approved flexible hose, the hose should not come in contact with the bottom of the appliance or any sharp edges. Flexible hose assemblies should be AS/NZS 1869 Class B or Class D certified.

Seal exposed bare edges of the cutout with an oil-based paint or moisture-proof polyurethane to prevent possible moisture creeping between the cooktop trim and the benchtop.

Take extreme care not to chip, crack, or break the top glass surfaces during installation. A heavy metal tool or part accidentally dropped on the glass could damage it.

If, after following the instructions given, correct performance cannot be achieved, please contact your nearest Fisher & Paykel Authorised Service Centre, Customer Care, or contact us through our website listed at the end of this document.

Page 1 Page 3
Page 2
Image 2
Fisher & Paykel CG603D, CG604D, CG451D, CG905D, CG903D, CG752D, CG302D Safety and Warnings, Electrical shock hazard
Page 1 Page 3

CG302D, CG752D, CG903D, CG905D, CG603D specifications

The Fisher & Paykel cooktops - CG604D, CG451D, CG603D, CG905D, and CG903D - are a range of high-performance cooking appliances designed for both professional chefs and home cooks alike. Known for their combination of advanced technology, innovative features, and sleek design, these cooktops meet the diverse needs of any culinary enthusiast.

The CG604D is a 60cm gas cooktop featuring four burners, including a high-power wok burner suitable for intense heat cooking. Its minimalist design seamlessly integrates into any kitchen, while the intuitive controls ensure ease of use. The cooktop is made from durable stainless steel, which not only adds to the aesthetic appeal but also offers easy cleaning and maintenance.

The CG451D is a unique 45cm model designed for smaller spaces without compromising on capability. This cooktop comes equipped with three versatile burners, including a powerful wok burner, ensuring that even space-restricted kitchens can cater to ambitious culinary projects. Its user-friendly design and robust construction make it a popular choice for urban dwellings.

The CG603D is a sophisticated 60cm cooktop with five burners, including a versatile simmer burner and a powerful triple-ring wok burner. Designed for flexibility, this cooktop allows for simultaneous cooking of various dishes. The glass ceramic surface adds an elegant touch while providing an easy-to-clean solution, catering to busy lifestyles.

The CG905D, measuring 90cm, is a heavy-duty option perfect for larger kitchens. It features five burners and a high-capacity wok burner, accommodating multiple cooking tasks simultaneously. Its robust stainless steel construction ensures durability, while the black glass surface adds a modern flair.

Lastly, the CG903D is also a 90cm cooktop tailored for high-performance cooking. With its intelligent flame controls and a unique dual wok burner, it delivers precision cooking for experienced chefs. The cooktop's design prioritizes both functionality and aesthetics, offering a contemporary touch to any kitchen.

Each of these Fisher & Paykel cooktops features advanced technologies such as flame failure safety devices, ensuring peace of mind during cooking. Furthermore, the design of the burners promotes even heat distribution, facilitating consistent cooking results. Whether it's a casual family meal or an elaborate dinner party, these cooktops provide the tools needed for any culinary endeavor.
Top Page Image Contents