The shipping container should contain the following items: power supply, HV output cable, male 15-pin "D" remote control connector and operator's manual. Examine the items immediately for damage. Locate the serial number label on the side of the power supply and verify the model number, the input voltage rating and the output voltage rating and polarity. In the event of any damage promptly notify the transportation company and the Lambda EMI Customer Service Manager.

    $  

The power supply can be mounted by the chassis support brackets (see Figure 2-1 and 2-2 for details). The mounting brackets are attached to the supply. The supply must mounted using four PHMS 8-32NC X 0.250 screws. Using wrong (longer) screws may short HV part to ground ,causing permanent damage to power supply. The power supply can also operate on a bench or table top. Power supplies >6kV with Oil H.V. section must be operated in upright position i.e. mounting bracket parallel to ground plane. In all cases adequate clearances must be provided for proper air flow and cable bends. Keep the minimum HV cable bend radius greater than 4 inches (101.6mm) to minimize stress on the insulation. Generally, at least 4 inches (101.6mm) of clearance should be allowed at the inlet of the power supply and 2 inches (50.8mm) at the sides.

When operating in an enclosed system, care must be taken to ensure the ambient inlet air to the power supply does not exceed the maximum operating temperature of 45°C. This often requires addition of a system heat exchanger.

 

Proper grounding from the input AC power is required to reduce the risk of electric shock. The metal chassis of the power supply is grounded through the green earthing wire at the input AC power terminal block. A protective ground connection by way of the grounding conductor in the input terminal is essential for safe operation. Use extreme caution when connecting input AC power and never apply the incorrect input power. (Figure 2-1 & 2-2).

The PFC version and version without PFC should be connected as explained in the following 2 paragraphs.

A.Version with no PFC.

For this version, the supply can be connected to either 110VAC or 220VAC input voltage. (See Table 2.2). These connections are shown in Figure 3-1.

1.For 110VAC connect the input line wires to L1 and COM terminals.

2.For 220VAC connect the input wires to L2 and COM terminals.

B.Version with PFC.

83-493-001 Revision G

3 - 1

Installation

Page 12 Page 14
Page 13
Image 13
Fluke pmn instruction manual , , $ ,
Page 12 Page 14

pmn specifications

Fluke PMN, or Fluke Precision Measurement Network, is an advanced solution designed to enhance the reliability and accuracy of metrology in various applications. This system is aimed at professionals in industries such as manufacturing, aerospace, telecommunications, and utilities, where precision measurement is critical.

One of the main features of Fluke PMN is its integrated measurement capabilities. The system combines multiple measurement functions, including voltage, current, resistance, frequency, and temperature, enabling users to perform comprehensive assessments without the need for multiple devices. This integration simplifies workflows and reduces the time spent on measurements.

Fluke PMN utilizes cutting-edge measurement technologies to ensure high accuracy and repeatability. One notable technology is its advanced digital signal processing, which minimizes noise and enhances the clarity of measurements. This results in significantly improved measurement precision, especially in complex environments where interference is prevalent.

Another key characteristic of Fluke PMN is its scalability. The system can be expanded with additional modules to adapt to the specific needs of a business. This modularity makes it a versatile choice for organizations looking to grow their measurement capabilities over time without the need for complete system overhauls.

Fluke PMN also supports remote monitoring and management through cloud technology. Users can access real-time data, generate reports, and perform analysis from virtually anywhere, making it easier to manage multiple measurement sites and maintain consistent quality standards across operations.

The user-friendly interface is another significant aspect of Fluke PMN. The intuitive design allows users to easily navigate through its various functions, ensuring that even personnel with minimal training can operate the system efficiently. This aspect greatly reduces the learning curve and improves overall productivity.

In addition to these features, Fluke PMN is built to withstand the rigors of industrial environments. Its durable construction ensures longevity and reliability, minimizing downtime due to equipment failure. This resilience is crucial for industries that depend on continuous operation and stringent adherence to quality control standards.

Overall, Fluke PMN represents a powerful solution for precision measurement. With its integrated capabilities, advanced technologies, scalability, remote monitoring, and robust design, it equips professionals with the tools they need to enhance accuracy, streamline operations, and uphold the highest standards of quality in their respective fields.
Top Page Image Contents