Fostex D2424LVMKII manual Recording in a new Program, Selecting the desired Program

Model D2424LVmkII Quick Operation Guide

Recording in a new Program

The explanation so far has been based on one Program set up when you format a current drive (E-IDE hard disk). You may create up to 99 Programs, depending on the available disk space.

Multiple Programs do not interfere with each other. You can record, play, and edit each Program independently, which facilitates song management. This section explains how to set up a new Program on the disk. Refer to the reference manual for more information regarding Programs.

<CAUTION>

•When creating a new program, the initial settings such as the tempo map are copied from the current program. For example, if the default tempo map is edited in the current program, the edited tempo map is copied to the newly created program.

•A new compilation is possible only when the “Chain Play?” (Setup of the chain play mode) menu in the SETUP mode is set to “Off.” If the [PGM SEL] key is pressed when the “Chain Play?” menu is set in other than the “Off” mode, the recorder will enter the “Chain Play mode”. Before starting compilation, check that the “Chain Play?” is “Off” and if it is not, be sure to reset it to “Off.”

1.While this recorder is stopped, press the [PGM SEL] key.

The display indicates “Select PGM!” momentarily, then shows the title of Program 1. The Program number and “SURE?” flash.

Flashing		Flashing
SURE?
			PGM
OL	OL	BIT	24
0	0
3	3			FS
6	6
9	9			kHz
12	12		CLOCK
18	18
24	24			INT
30	30
42	42
∞	∞

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

2.Turn the Jog dial clockwise to select“New Program?”.

The “?” mark of “New Program?”, and “SURE?” flash, indicating that you can set up a new Program.

Flashing Flashing

			SURE?																						PGM
OL																							OL	BIT	24
0																							0
3																							3		FS
6																							6
9																							9		kHz
12																							12		CLOCK
18																							18
24																							24		INT
30																							30
42																							42
∞																							∞
1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16	17	18	19	20	21	22	23	24

Normally, any new program that is compiled will be in the sampling frequency set when formatting the current drive. However, in this recorder, it is possible to change the program sampling frequency.

In other words, programs with different sampling frequencies can be made in the current drive and thus recording can be matched to a chosen task. For details refer to the next page.

<Selecting the desired Program>

If you have set up multiple Programs on the disk, you first need to select the target Program prior to recording, playback, or edit. To select a Program, follow the steps below. Do not select a different Program until you finish the session.

1.While this recorder is stopped, press the [PGM SEL] key.

“Select PGM!” appears momentarily, then the number and title of the current Program appear.

3.Press the [EXECUTE/YES] key.

This recorder sets up a new Program (Program 2) and enters the “Title Edit?” menu in SETUP mode, showing the following display. In this example, we use the default title.

You can change the title later. Refer to the Reference manual for more information.

Flashing

SETUP			PGM
OL	OL	BIT	24
0	0
3	3		FS
6	6
9	9		kHz
12	12		CLOCK
18	18
24	24		INT
30	30
42	42
∞	∞

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

4.Press the [EXIT/NO] key.

This recorder exits SETUP mode, and the top of Program 2 in ABS Time Base (ABS 0) appears.

																				ABS
																						M	S		F
																									PGM
OL																							OL	BIT	24
0																							0
3																							3		FS
6																							6
9																							9		kHz
12																							12		CLOCK
18																							18
24																							24		INT
30																							30
42																							42
∞																							∞
1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16	17	18	19	20	21	22	23	24

2.Turn the Jog dial clockwise or counter-clockwise.

The numbers and titles of the Programs on the disk appear in turn.

3.Select the desired Program number and press the [EXECUTE/YES] key.

The top of the selected Program appears in ABS Time Base (ABS 0).

22