Fostex RM-2 owner manual Stereo Mono L+R Mono L only Mono R only, Rear panel

5) [CH SEL] (channel select) key

This key switches the channel(s) to be monitored.

Each press of the key switches the channel(s) in the following order (by default when turning on the power, "stereo" is selected). The current selection is shown by the indicators in the status information section (see page 6 for the indication of channel selection).

Stereo

Mono (L+R)

Mono (L only)

Mono (R only)

By long press of the [CH SEL] key, you can mute the unit, while the [MUTE] indicator flashes (this is called "user mute"). Pressing the [CH SEL] key again release muting and the [MUTE] indicator turns off. See page 6 for the user mute func- tion.

Model RM-2 Owner’s Manual

The following shows which signal is output from each internal speaker unit for each channel se- lection.

When "Stereo" is selected

L	VU -			-			R
	PEAK	-		-
		RM-2				ANALOG
						CH SEL INPUT
		STEREO RACK MONITOR	PHONES	L R		DIGITAL
				MIN	MAX
When "Mono (L+R)" is selected
L+R	VU -			-			L+R
	PEAK	-		-
		RM-2				CH SEL INPUT
		STEREO RACK MONITOR				ANALOG
			PHONES	L RMIN	MAX	DIGITAL
When "Mono (L only)" is selected
L	VU -			-			L
	PEAK	-		-
		RM-2				CH SEL INPUT
		STEREO RACK MONITOR				ANALOG
			PHONES	L RMIN	MAX	DIGITAL
When "Mono (R only)" is selected
R	VU -			-			R
	PEAK	-		-
		RM-2				CH SEL INPUT
		STEREO RACK MONITOR				ANALOG
			PHONES	L RMIN	MAX	DIGITAL

6)Monitor output level controls

These dual concentric controls adjust the speaker output (or headphones output) levels. The outer control adjusts the left channel level, while the inner control adjusts the right channel level.

7)PHONES jack

This jack is used for connecting headphones. When a plug is inserted, the internal speakers are cut.

<Rear panel>

RL

ANALOG INPUT

		CAUTION
		AVIS: RISQUE DE CHOC ELECTRIQUE
		NE PAS OUVRIR
		WARNING:
		TO REDUCE THE RISK OF FIRE OR ELECTRIC
		SHOCK, DO NOT EXPOSE THIS EQUIPMENT
DIGITAL	INPUT	TO RAIN OR MOISTURE.

ON

OFF

POWER AC IN

8 9

8) [ANALOG INPUT] connectors (XLR / 1/4" combi-

jacks)

You can connect an XLR-3-12C connector or 1/4" plug to each of these combi-jack type [ANALOG INPUT] connectors (you cannot insert both together). Each connector accepts a +4 dBu analog signal via XLR connection or a -10 dBV analog signal via 1/4" connection.

				HOT (+)	COLD (-)	Ground
2		1
	3		XLR	Pin 2	Pin 3	Pin 1

1011

10)[POWER] switch

This switch turns the power on or off.

Each time you turn on the power, the RM-2 is muted for preventing the noise from being generated from the speaker units (the "MUTE" indicator flashes).

11) [AC IN] connector

Connect to the AC outlet using the supplied power cord.

Make sure that the AC outlet voltage matches the unit.

9)[DIGITAL INPUT] connector (XLR connector)

This connector accepts an AES/EBU digital signal at the sampling frequency within the 44.1 kHz to 96 kHz range. You can connect an XLR- 3-12C connector.

21

3

HOT (+) COLD (-) Ground

XLR Pin 2 Pin 3 Pin 1

5