45
Mixer Functions
Effect parameter details

The parameters that can be adjusted will depend on the parameter type.

Reverb effect parameters (parameter type: REVERB)

For effect types 1--24 of the preceding "Effect type" table, the following four parameters can be adjusted.

1.Eff Level Adjust the effect return level: 0~99
2.Rev Time Adjust the length of reverberation. Range: 0.1--9.9 seconds
3.Pre Delay Adjust the time from the original sound until reverberation begins. Range: 0--100 ms
4.Hi Ratio Adjust the decay ratio of the high frequencies. Range: 0--10
5.E/R Level Adjust the volume of the early reflections. Range: 0--99

Delay+reverb effect parameters (parameter type: DELAY+REVERB)

For effect types 25--28 of the preceding "Effect type" table, the following four parameters can be adjusted.

1.Eff Level Adjust the effect return level: 0~99
2.Delay Time Adjust the delay time: Range: 1--230 ms
3.Feedback Adjust the number of delay repeats. Range: 0--99
4.Delay Bal Adjust the delay balance. Range: 0--99
5.Rev Time Adjust the length of reverberation. Range: 0.1--9.9 seconds

Delay effect parameters (parameter type: DELAY)

For effect types 29 and 30 of the preceding "Effect type" table, the following four parameters can be adjusted.

1.Eff Level Adjust the effect return level: 0~99
2.Delay Time Adjust the delay time. Range: 1--680 ms
3.Feedback Adjust the number of delay repeats. Range: 0--99
4.Hi Ratio Adjust the decay ratio of the high frequencies. Range: 0--10
5.Filter Adjust the tone of the delay sound. Range: L9~L1, OFF, H1~H9
*L1~L9 = LPF (larger numbers will lower the cutoff frequency)
*H1~H9 = HPF (larger numbers will raise the cutoff frequency)

BPM delay effect parameters (parameter type: BPM DELAY)

For effect types 31 and 32 of the preceding "Effect type" table, the following four parameters can be adjusted.

1.Eff Level Adjust the effect return level: 0~99
2.BPM Adjust the BPM. Range: 30--250 bpm
3.Note Select the note value for the delay. Range: 24, 16, 8T, 16...8, 4T, 8., 4, 2T, 4., 2, 2., 1
*24 = 16th note sextuplets, 16 = 16th notes, 8T = 8th note triplets, 16. = dotted sixteenth notes,
8 = 8th notes, 4T = quarter note triplets, 8. = dotted eighth notes,
4 = quarter notes, 2T = half-note triplets, 4. = dotted quarter notes, 2 = half notes
* The "." shown in the ninth character of the LCD indicates a dotted note.
* The "T" shown in the ninth character of the LCD indicates a triplet.
4.Feedback Adjust the number of delay repeats. Range: 0--99 (100 steps in increments of 1)
5.Filter Adjust the tone of the delay sound. Range: L9~L1, OFF, H1~H9
*L1~L9 = LPF (larger numbers will lower the cutoff frequency)
*H1~H9 = HPF (larger numbers will raise the cutoff frequency)

Short delay effect parameters (parameter type: SHORT DELAY)

For effect type 33 of the preceding "Effect type" table, the following four parameters can be adjusted.

1.Eff Level Adjust the effect return level: 0~99
2.Delay Time Adjust the delay time. Range: 0.1--9.9 ms, 10--99 ms, 100--200 ms
3.Feedback Adjust the number of delay repeats. Range: 0--99
4.Hi Ratio Adjust the decay ratio of the high frequencies. Range: 0--10
5.Filter Adjust the tone of the delay sound. Range: L9~L1, OFF, H1~H9
*L1~L9 = LPF (larger numbers will lower the cutoff frequency)
*H1~H9 = HPF (larger numbers will raise the cutoff frequency)

Doubling effect parameters (parameter type: DOUBLING)

For effect type 34 of the preceding "Effect type" table, the following three parameters can be adjusted.

1.Eff Level Adjust the effect return level: 0~99
2.Lch Delay Adjust the delay time of the L channel. Range: 0.1--9.9 ms, 10--99 ms, 100--200 ms
3.Rch Delay Adjust the delay time of the R channel. Range: 0.1--9.9 ms, 10--99ms, 100--200 ms
4.Filter Adjust the tone of the delay sound. Range: L9~L1, OFF, H1~H9
*L1~L9 = LPF (larger numbers will lower the cutoff frequency)
*H1~H9 = HPF (larger numbers will raise the cutoff frequency)