INSTALLATION - RECESSED |
|
|
|
| ||
For A. D. A. compliance, top of lower double stud should be |
| 1" |
|
|
| |
30.5“ (78 cm) from the floor. | (25.4 mm) | (571 mm) |
|
|
| |
|
|
|
|
|
| |
Recommended Blocking: |
|
|
|
| TOP | |
|
|
|
| (98.6 mm) | VIEW | |
Wood double stud blocking is necessary. Contact an architect and |
|
|
|
| ||
|
|
|
| |||
building official to make sure the blocking is adequate and complies |
|
|
|
| ||
|
| Double Stud |
|
|
| |
with building codes (Fig. b). |
|
|
|
|
| |
|
|
|
|
|
| |
1. Slide changer into blocking area and mark mounting hole location |
|
|
|
| FRONT | |
on blocking studs. |
| DoubleStud | DoubleStud | (867 mm) | VIEW | |
HINT: This may require 2 additional people to help hold changer |
|
| ||||
in position while you are marking the locations. |
|
| (775 mm) |
|
|
|
2. Shim changer for a snug fit. |
|
|
|
|
|
|
3. Align holes in changer with marked holes and secure using the |
|
|
|
|
|
|
appropriate fasteners (Fig. c). | For A. D. A. |
| Double Stud |
|
|
|
NOTE: It is installers responsibility to provide correct fastereners | (78 cm) |
|
|
|
|
|
| Compliance |
|
| Fig. b |
|
|
for other substrates. | 30.5” |
|
|
|
| |
| A. F. F |
|
|
| ||
4. Ensure all six (6) fasteners are tight. |
|
|
| Recess |
| Recess |
|
|
| Mounting | |||
|
|
| Recess | Holes |
| Mounting |
|
|
|
|
| Holes | |
|
| Mounting |
|
|
| |
|
|
| Holes |
|
|
|
INSTALLATION - SURFACE-MOUNT
Fig. c
Recommended Blocking:
If the walls do not have studs on center, then additional blocking is necessary (Fig. d).
Contact an architect or building contractor to make sure the blocking is adequate and complies with building codes.
For A. D. A. compliance, measure up 62 3/4” (159 cm) from the floor and mark the wall. This locates the position for the top left attachment hole.
NOTE:- Changer MUST be mounted to studs (Fig. e).
- This unit incorporates a finishing collar that seats behind the changer’s outside flange. Center the collar as the unit is being tightened against the wall (Fig. f).
Collar
Top
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 16" |
|
|
| |
|
| 26" |
|
|
|
|
|
| ||||
For A. D. A. |
| (660 mm) |
|
|
| (406 mm) |
|
|
| |||
Compliance |
| on center |
|
|
| on center |
|
| ||||
62 3/4” |
|
|
|
|
|
|
|
|
|
|
| |
(159 cm) |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| A. F. F |
|
|
|
|
|
|
| |||
|
|
|
| Fig. d | ||||||||
|
|
|
|
|
|
|
| |||||
|
|
|
|
| ||||||||
|
|
|
|
|
|
| Holes | |||||
Wall
2
Unit |
|
Fig. f | Fig. e |
|
