ELECTRICAL CONNECTIONS

FOR 3-WIRE SYSTEM

USA ELECTRIC Dryer

1.Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer upper corner.

2.Install a U.L. approved strain relief into the power cord entry hole of the mounting bracket. Finger tighten the nut only at this time.

GREEN

 

GROUND

SILVER TERMINAL

SCREW

ELECTRICAL CONNECTIONS FOR 4-WIRE SYSTEM

USA ELECTRIC Dryer

1.Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer upper corner.

2.Install a U.L. approved strain relief in the entry hole of the mounting bracket. Finger tighten the nut only at this time.

3.Remove the ground wire from the green ground screw located above the terminal block.

 

 

GREEN POWER

CORD

 

GREEN

GROUND WIRE

 

 

GROUND

 

SILVER TERMINAL

NEUTRAL

GROUND

WIRE

STRAIN

RELIEF

MOUNTING

BRACKET

NUT

TIGHTEN NUT

TO THESE

THREADS

POWER CORD

SCREW

TERMINAL BLOCK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TIGHTEN NUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BLACK

 

NEUTRAL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TO THESE

 

 

GROUND

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

THREADS

 

 

 

 

 

 

 

 

 

 

 

WHITE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NUT

 

 

 

 

 

 

 

RED

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

STRAIN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RELIEF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MOUNTING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

POWER CORD

 

 

 

 

 

 

 

3.Thread a U.L. approved 30 amp. power cord, NEMA 10-30 type SRDT, through the strain relief.

4.Attach the power cord neutral (center wire) conductor to the silver colored center terminal on the terminal block. Tighten the screw securely.

5.Attach the remaining two power cord outer conductors to the outer brass colored terminals on the terminal block. Tighten both screws securely.

Do not make a sharp bend or crimp wiring/ conductor at connections.

6.Reattach the strain relief mounting bracket to the back of the dryer with two screws. Tighten screws securely.

7.Tighten the screws securing the cord restraint firmly against the power cord.

8.Tighten the strain relief nut securely so that the strain relief does not turn.

9.Reinstall the terminal block cover.

4.Thread a U.L. approved 30 amp power cord, NEMA 14-30 type ST or SRDT through the strain relief.

TYPICAL 4

TYPICAL

4

 

BLACK

CONDUCTOR

CONDUCTOR

 

WHITE

 

 

30 AMP NEMA 14-30 TYPE SRDT OR ST

 

RED

 

 

 

 

GR

EEN

 

 

5.Attach the green power cord ground wire to the cabinet with the green ground screw.

6.Attach the white (neutral) power cord conductor from the power cord and the neutral ground wire from the dryer harness to the silver-colored center terminal on the terminal block. Tighten the screw securely.

7.Attach the red and black power cord conductors to the outer brass-colored terminals on the terminal block.

Do not make a sharp bend or crimp wiring/ conductor at the connections.

8.Tighten the screws securing the cord restraint firmly against the power cord.

9.Tighten the strain relief nut securely so the strain relief does not turn.

10.Reinstall the terminal block access cover.

12

Page 12
Image 12
Frigidaire 137101400 Electrical Connections For 3-WIRE System, Electrical Connections for 4-WIRE System