Avoid Service Checklist

OCCURRENCE

Before calling for service, review this list. It may save you time and expense. This list includes common occurrences that are not the result of defective workmanship or

materials in this appliance

SOLUTION

Air conditioner will not operate. Wall plug disconnected. Push plug firmly into wall outlet.

Current device tripped. Preset RESET button.

House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker.

Control is OFF. Turn control On and set to desired FAN or COOL setting.

Air from unit does not feel cold enough.

Room temperature below 60 F (15 C). Cooling may not occur until room temperature rises above 60 F (15 C).

Temperature sensor touching cold coil, located behind air filter. Straighten away from coil

Reset to a lower temperature.

Compressor shut-off by changing modes. Wait approximately 3 minutes, and listen for compressor to restart when set in the COOL mode.

Air conditioner cooling, but	Outdoor		temperature below 60 F (15 C). To defrost the coil, set selector to		FAN
room is too warm- ice forming	position.
on cooling coil behind
on cooling coil behind	Air filter may be dirty. Clean filter. Refer to Care and Cleaning section. To defrost, set
decorative front.
	selector to FAN ONLY mode..
	Temperature is too low for night-time cooling. To defrost the coil, set to FAN ONLY
	mode. Then, set temperature to a higher number.
Air conditioner cooling, but	Dirty air filter-air restricted. Clean air filter. Refer to Care and Cleaning section.
room is too warm-NO ice
room is too warm-NO ice	Temperature is too high. Set temperature to a lower number.
forming on cooling coil	Temperature is too high. Set temperature to a lower number.
behind decorative front.	Vent set at OPEN position. Set vent at CLOSED position for maximum cooling.
	Air direction louvers positioned improperly. Position louvers for better air distribution.

	Front of unit is blocked by drapes, blinds, furniture, etc.-restricts air distribution.Clear
	blockage in front of unit.
	Doors,	windows, registers, etc, open- cold air escapes. Close doors, windows,
	registers, etc.
	Unit recently turned on in hot room, allow additional time to remove “ stored heat”
	from walls, ceiling, floor and furniture.
Room too cold	Setting too low. Increase temperature setting.
Air conditioner turns on and	Dirty air filter-air restricted. Clean air filter.
off rapidly.	Outside		temperature extremely hot. Set FAN speed to a faster setting to bring air
	past cooling coils more frequently.

Noise when unit is cooling	Air movement sound. This is normal. If too loud, set to a slower FAN setting.
	Sound	of fan hitting water-moisture removal system. This is normal when humidity
	is high. Close doors windows and registers.
	Window		vibration- poor installation. Refer	to installation instructions or check with
	installer.
Water dripping INSIDE when	Improper		installation. Tilt air conditioner	slightly to the outside to allow	water
unit is cooling.	drainage. Refer to installation instructions -check with installer.

Water dripping OUTSIDE when	Unit removing large quantity of moisture from humid room. This is normal during
unit is cooling.	excessively humid days.

819042150-01 specifications

The Frigidaire 819042150-01 is a highly regarded refrigerator part that plays a crucial role in maintaining the efficiency and functionality of various Frigidaire refrigerator models. This specific component is commonly known as the refrigerator door seal, also referred to as a door gasket.

One of the main features of the Frigidaire 819042150-01 is its durable construction. Made from high-quality materials, this door seal is designed to withstand the wear and tear associated with daily use. Its robust design not only ensures a long lifespan but also contributes to the overall energy efficiency of the refrigerator. Proper sealing is essential as it helps to maintain the internal temperature, reducing the workload on the compressor and ultimately saving energy.

The technology behind the Frigidaire 819042150-01 is centered around its ability to create an effective airtight seal. This feature is critical in preventing cold air from escaping and warm air from entering the refrigerator. An effective gasket allows for consistent temperature regulation, which is vital for keeping food fresh longer. The design of the gasket incorporates magnetic strips that reinforce the seal, ensuring that the door closes snugly after each use.

Another characteristic of the Frigidaire 819042150-01 is its easy installation process. Designed to be a direct replacement for old or worn-out door seals, it allows homeowners to quickly restore their refrigerator’s efficiency without needing professional help. Typically, customers can install this part in a matter of minutes, which adds to its appeal for DIY enthusiasts.

Furthermore, the Frigidaire 819042150-01 is compatible with a variety of Frigidaire refrigerator models, making it a versatile choice for many homeowners. This compatibility means that users can conveniently source a replacement part without worrying about fitment issues.

In summary, the Frigidaire 819042150-01 is a vital component that enhances the performance of Frigidaire refrigerators. With its durable construction, effective airtight sealing technology, ease of installation, and compatibility with multiple models, this door gasket is an essential part for any fridge owner aiming to maintain optimal refrigeration performance while ensuring energy efficiency. Its role cannot be overstated, as it directly impacts food preservation, energy consumption, and overall user satisfaction.

Frigidaire 819042150-01 manual Avoid Service Checklist

Models: 819042150-01