Frymaster BIH52, MH52 - page 11

2-2

NATIONAL CODE REQUIREMENTS

The type of gas for which the fryer is equipped is stamped on the data plate attached to the inside of

the fryer door. Connect a fryer stamped “NAT” only to natural gas, those stamped “PRO” only to

propane gas, and those stamped “MFG” only to manufactured gas.

Installation shall be made with a gas connector that complies with national and local codes, and,

where applicable, CE codes. Quick-disconnect devices, if used, shall likewise comply with national,

local, and, if applicable, CE codes.

ELECTRICAL GROUNDING REQUIREMENTS

All electrically operated appliances must be grounded in accordance with all applicable national and

local codes, and, where applicable, CE codes. A wiring diagram is located on the inside of the fryer

door. Refer to the rating plate on the inside of the fryer door for proper voltages.

DANGER

If this appliance is equipped with a three-prong (grounding) plug, it must be plugged

directly into a properly grounded receptacle.

Do not cut or remove the grounding prong from the plug.

DANGER

This equipment requires electrical power for operation.

Place the gas control valve in the OFF position in case of a prolonged power outage.

Do not attempt to use the equipment during a power outage.

FCC COMPLIANCE

The user is cautioned that any changes or modifications to Frymaster computers not expressly ap-

proved by the party responsible for compliance could void the user’s authority to operate the equip-

ment.

Frymaster computers have been tested and found to comply with the limits for a Class A digital de-

vice, pursuant to Part 15 of the FCC rules. While these devices are verified as Class A devices, they

have been shown to meet the Class B limits. These limits are designed to provide reasonable protec-

tion against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of the equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

If necessary, the user should consult the dealer or an experienced radio and television technician for

additional suggestions.

Contents

Main SERVICE MANUAL FRYMASTER MH52 AND BIH52 SERIES GAS FRYERS *8195423* Page Page WARRANTY STATEMENT Page Page Page CHAPTER 1: INTRODUCTION Page CHAPTER 2: INSTALLATION INSTRUCTIONS Page Page Page 2-5 Required airflow for the combustion air supply is 2m3/h per kW. Page Page CHAPTER 3: SERVICE PROCEDURES, TROUBLESHOOTING AND WIRING DIAGRAMS Page Page 3-4 CURRENT FLOW THROUGH INTERFACE BOARDS 806-3398 AND 106-0386 (H52 APPLICATION) J3 LEFT VAT FULL OR RIGHT VAT J2 Page Honeywell 3-7 CE Standard Burner Manifold Gas Pressures for Fryers Manufactured Through April 1999 Non-CE Standard Burner Manifold Gas Pressures Page Page Page Page Page Page Page Page Page Page Disassembling A Frypot Spacer 3-18 (Full Vat Illustrated) Spacers Re-assembling A Frypot 3-19 (Full Vat Illustrated) here Apply cement Page Page Page Page Page Page Page Page Page Page 3-30 3.8.1 Troubleshooting the 24VAC Circuit 3-31 FULL OR RIGHT VAT LEFT VAT 3-32 24 VOLT CIRCUIT With Interface Board 806-3398 or 106-0386 and One 807-3366 (FV) Ignition Module 3-33 3.8.2 Troubleshooting the Gas Valve 3-34 3.8.3 Troubleshooting the Temperature Probe Note: Disconnect computer before measuring probe resistance. 3-35 3.9 Probe Resistance Chart Probe Resistance Chart For use with H52 Series fryers manufactured with Minco Thermistor probes only. FOHMSC FOHMSC FOHMSC FOHMSC FOHMSC 3-36 Probe Resistance Chart (Continued) For use with H52 Series fryers manufactured with Minco Thermistor probes only. FOHMSC FOHMSC FOHMSC FOHMSC FOHMSC 3-37 3.10 Simplified Wiring Diagrams H52 SERIES FULL-VAT JUNE 1996 - JULY 1999 DRAIN SAFETY SWITCH ONLY ON BIH52 MODELS AIR SWITCH ONLY ON CE AND SOME EXPORT UNITS HOOD RELAY 3-38 H52 SERIES FULL-VAT BEFORE JUNE 1996 & AFTER JULY 1999 MODULE LEFT IGNITION MODULE LINE VOLTAGE H52 SERIES FULL-VAT WITH ONE DUAL-SPARK IGNITION MODULE SINGLE-SPARK IGNITION BE EQUIPPED WITH TWO MODULE. OTHERS MAY DUAL-SPARK IGNITION H52 SERIES DUAL-VAT JUNE 1996 - JULY 1999 MODULE LEFT IGNITION MODULE DRAIN SAFETY SWITCH H52 SERIES DUAL-VAT BEFORE JUNE 1996 & AFTER JULY 1999 MODULE LEFT IGNITION MODULE (TWO DUAL-FUNCTION HEAT/BLOWER RELAYS (K1 & K2) AND TWO IGNITION MODU LES) 3-42 3.11 Principal Wiring Connections C4 C1 J3 BIH152 Main Wiring Diagram (U.S., CE, and Non-CE Export) 8050926E T M 3-44 8050502G BIH52/MH52 Main Wiring Diagram (U.S. and Non-CE Export) Old Single-Spark Ignition Module PWR WHT 2 BIH52/MH52 Main Wiring Diagram (U.S. and Non-CE Export) New Dual-Spark Ignition Module 3-46 BLACK C5 BIH52/MH52 Main Wiring Diagram (CE) Old Single-Spark Ignition Module BIH52 Filter Box Wiring Diagram (U.S., CE, and Non-CE Export) 3-47 3-48 MH152 Transformer Wiring Diagram (U. S. and Non-CE Export) 120V CONFIGURATION SHOWN 2 31 N 8050504C MH152 Transformer Wiring Diagram (CE) BIH252/MH252 Transformer Box Wiring Diagram (U.S. and Non-CE Export) 3-50 BIH352/MH352 Transformer Box Wiring Diagram (U.S. and Non-CE Export) 3-51 3-52 8050500E 56 BIH452/MH452 Transformer Box Wiring Diagram (U.S. and Non-CE Export) 120 VOLTS 2 LINECOM 14 1 56 BIH452/MH452 Transformer Box Wiring Diagram (CE) 18C BLUE FRYER 1 6C BLUE NOTE: Also used for CE BIH252/MH252 and CE BIH352/MH352 Transformer Boxes. CHAPTER 4: PARTS LIST 4-2 4.2 Cabinetry Components 4.2 .1 BIH152 and MH152 Cabinet Components MH152 BIH152 Page 4-4 4.2.2 BIH52 Cabinet Components (Batteries) Detail of Gusset and Filter Rail Construction Detail of Base Assembly Construction NOTE: Items 26 and 27 are not used on CE units. 4-5 4.2.2 BIH152 Cabinet Components (Batteries) cont. Page 4-7 4.2.3 MH52 Cabinet Components (Batteries) cont. * Not illustrated. LIST CONTINUED ON NEXT PAGE Page Page 4-9 4.2.4 BIH52/MH52 Cap-N-Splash Assemblies, Fluecaps, Standoffs and Related Parts Page Page Page 4-13 4.3 Combustion System, Frypot and Gas System Components 4.3.1 Blowers and Associated Parts 4-14 4.3.2 Ignition Sub-System Components ITEM PART # COMPONENT 4-15 4.3.3 Frypot Assembly Components 4.3.3.1 Full Vat Kits.) Kits and Insulation Full Vat Frypot 4-16 4-17 4.3.3.2 Dual Vat Kits and Insulation Dual Vat Frypot Components (See Page 4-19 for list of Service Frypot 4-18 Page Page 4-21 4.3.6 Gas Manifolds BIH52/MH52 Multi-Fryer Units Typical Configuration for Systems using non-CE Gas Valves 826-1122 or 826-1123 Typical Configuration for Systems using CE Gas Valve 810-1715 Full Vat (left) and Dual Vat (right) Manufactured Gas Configurations (MH52 and BIH52) Page 4-23 4.3.7 Gas Valves, Gas Lines and Fittings Page 4-25 4.4 Electronics 4.4.1 Computers, Controllers and Associated Components 2 1 1 2 Discontinued M100B Computer. Replaced by M2000 computer. Page 4-27 4.4.2 Component Boxes Page 4-29 4.4.4 Transformer Box Components ssy. PN 806-8338SP BIH452/MH452 BIH152 4-30 Page Power Cords NOTES: 4-34 4-35 4.5.1.2 Drain Valve Assemblies and Associated Components Locknut separate items. face-to-face. 4-36 4-37 4.5.2 Filtration System Components 4.5.2.1 Filter Base Assemblies Page 4-39 4.5.2.2 Filter Motor and Pump Plumbing Prior to September 1999 Standard BIH52 Filter Motor and Pump September 1999 and Later 4-40 4-41 4.5.2.3 Filter Pan Assemblies and Associated Components Page 4-43 4.5.2.4 Rear Flush Oil Return Components NOTE: