FujiFilm FinePix S3 1, 2, 3

50 51

Advanced Photography

The release mode is normally set to Single-frame. Set the release mode to Continuous Shooting to

take sequential shots of moving subjects or to take a series of shots using Auto Exposure

Bracketing.

In this mode, one shot is taken each time you press the shutter button. Use this mode to take a

single clearly defined shot in each frame.

●

If you take a number of single-frame shots in rapid succession, the number of available shots is highlighted in the same

way as in continuous shooting. Once this happens, no further shots can be taken. Wait until the number of available shots

is no longer highlighted.

,SINGLE-FRAME

This mode allows you to take up to 12 consecutive shots by holding down the shutter button (Max.

2.5 frames/sec.).

hOnce you have shot the maximum number of continuous frames, the number of available shots

shown on the rear display panel is highlighted. No further continuous shots can be taken at that

point. Wait until the number of available shots is no longer highlighted.

The number of available frame and the maximum number of continuous frames varies depending

on the dynamic range (D-RANGE) and quality settings in SET-UP.

.CONTINUOUS SHOOTING

Hold down the release mode switch unlock button

and set the release mode switch to “,” (Single-

frame) or “.” (Continuous Shooting).

ISO200

09 / 23 / 2004

10 : 00 AM

ISO200

09 / 23 / 2004

10 : 00 AM

●

You cannot use continuous shooting with the built-in flash.

●

If “ON” or “PREVIEW” is selected for “IMAGE DISP.” (➡P.103) when continuous shooting is used, only the photographed

image for the final frame is displayed and automatically recorded.

●

If you use continuous shooting when the number of available shots is low, the number of available shots may temporarily

change to 0.

9SELF-TIMER PHOTOGRAPHY

RELEASE MODES

You can use the self-timer when you want to be in the photograph. Use a tripod or place the camera

on a stable surface before using the self-timer.

1Hold down the release mode switch unlock button

and set the release mode switch to “9” self-timer.

21Position the focus area over the subject.

2Press the shutter button down halfway to focus

the shot.

3Without releasing the shutter button, press the

shutter button down fully to start the self-timer.

3The self-timer lamp flashes for 8 seconds and then

stays lit for 2 seconds, after which the shot is taken.

hPress the “MENU/OK”, “FUNC” or “PLAY” button

to cancel self-timer shooting.

hYou can change the self-timer running time from

10 seconds to 2, 5 or 20 seconds (➡P.112).

◆Before shooting ◆

hThe self timer does not operate in situations where the camera shutter is disabled, such as when the

focus is not set in AF-S (Single-AF Servo) mode.

hIn exposure modes other than “M” (Manual), you must prevent any back-entry light from the eyepiece

to obtain the correct exposure. Before pressing the shutter button, cover the eyepiece with your hand

or the eyepiece cap provided. To attach the eyepiece cap, remove the rubber eyecup and slide the

cap down over the eyepiece from above.

hDo not stand in front of the lens when setting the self-timer in autofocus mode.

D-RANGE setting in SET-UP WIDE STANDARD

Quality HIGH FINE, NORMAL HIGH FINE, NORMAL

RAW JPEG RAW JPEG

Max. number of available frames

Max. 1.4 frames/sec. Max. 1 frame/sec.

Max. 2.5 frames/sec.

Max. continuous frames 3 6 7

Minimum shooting interval in

multiple exposure shooting Max. 1.4 frames/sec. Max. 2.5 frames/sec.

Max. no. of consecutive shots in

multiple exposure shooting 37

,SINGLE-FRAME /

.CONTINUOUS SHOOTING

RELEASE MODES