Fujitsu PG-LND101 6.2

6 VLAN 73

E

6.2 Creating VLAN

Perform the following procedures to create a VLAN.

1Log on with administrator privileges.

2Set the port of the switch connected to the Ethernet controller to

enable send/receive of VLAN tag frames.

3Click [Start] → [Settings] → [Control Panel] → [Intel®PROSet

Wired], and start Intel® PROSet.

4Select LAN adapter to set VLAN, and right click.

A VLAN cannot be set to an adapter composing a team.

5Click [Add VLAN].

6Set [ID] and [Name], then click [OK].

[ID] must be the same as the set values on the switch. The available range to set is 1 to 4094.

[Name] does not need to be the same as the setting on the switch.

When the confirmation message appears, select [Yes].

7Repeat Steps 4 through 6 to set respective VLANs.

8Click [OK] and exit Intel® PROSet.

When configuring a VLAN is completed, a virtual adapter "Intel(R) Advanced Network

Services Virtual Adapter" will appear.

Upper layer protocol is bound to this virtual adapter.

You cannot bind them with the Ethernet controller that makes up a Team.

IP address is set in this virtual adapter.

9Restart the system.

Contents

Main Page Page Page Page Page LAN 1.1 1.2 LAN 2.1 2.1.1 LAN 2.1.2 LAN Page 2.2 2.2.1 LAN 2.2.2 LAN Page Page 6 7 Page LAN LAN 3.1 3.1.1 3.2 3.2.1 2 3 3.2.2 LAN Windows Server 2003 Windows 2000 Server 1 2 Page 3.2.3 LAN Page 3.2.4 Page Intel PROSet Intel PROSet 4.1 4.2 Server 4.3 2 FMWORLD.NET ProSet.EXE 4.5 4.5.1 2 3 4 AFT/ALB/SFT AFT/ALB/SFT 5.1 AFT/ALB SFT Page LAN OS BX600BX660 BX620 S2 LCB Windows 5.2 5.3 5.4 5.5 VLAN VLAN 6.1 6.2 6.3 A A.1 A.2 A.3 Page Before Reading This Manual Remarks Warning Descriptions CAUTION WARNIN G Key Descriptions / Operations Abbreviations Safety WARNING CAUTION Check the items supplied Contents 1Gbit/s Ethernet I/O Module This chapter explains the features and specifications of this product. 1.1 1.2 `A server blade installed with a 1Gbit/s Ethernet I/O Module and a server blade installed with a 2Gbit/s FC I/O Module cannot be installed to the same chassis. `When a Switch Blade or a GbE Pass-Thru Blade is installed to network blade slot 3 or 4 (NET3 or 4), a FC Pass-Thru Blade cannot be installed at the same time. Installing a 1Gbit/s Ethernet I/O Module WARNING CAUTION 2.1 2.1.1 Location of 1Gbit/s Ethernet I/O Module Installation 2.1.2 Installing a 1Gbit/s Ethernet I/O Module 1 2 Page Installing the LAN Driver This chapter explains how to install the LAN driver. The versions of the module included in the LAN driver are as follows. 3.1 This product runs on the following LAN driver. 3.2 This section explains LAN drivers corresponding to Windows. 3.2.1 Installing the Driver 1 2 The [Computer Management] window appears. 3 Unrecognized network adapters Recognized network adapters 3.2.2 Updating LAN Drivers Page 3.2.3 Installing the LAN Driver Page Page 3.2.4 Removing the Driver Intel PROSet This chapter explains Intel PROSet. PRIMERGY server. 4.1 4.2 2000 Server System 4.3 1 2 downloaded from the Fujitsu PRIMERGY website. 4.4 4.5 4.5.1 Test Method 4.5.2 Actions to Take When an Error Occurs Teaming(AFT/ALB/SFT) This chapter explains Teaming (AFT/ALB/SFT). 5.1 AFT/ALB SFT Note Tea min g 1 Gbi t/ s Et her ne t I/O Module during use When performing teaming using LCB, refer to the latest release note. Windows 5.2 5.3 5.4 Notes 5.5 Modules Composing a Team and Replacing a Defective Card VLAN This chapter explains VLAN. 6.1 Notes 6.2 6.3 Appendix A A.1 A.2 A.3 Appendix B Contact Information Page