3. Connect cables to the ScanSnap.zUse only the cables supplied with the ScanSnap.

zTo power on the ScanSnap, the USB cable and either of the power cables (power cable or USB bus power cable) are need to be connected.

zWhen connecting to a USB hub, be sure to connect the ScanSnap to the hub nearest to your computer (first stage). If the ScanSnap is connected to a USB hub from the second stage onwards, it may not operate correctly.

zIf connecting the ScanSnap with USB 2.0, make sure that the USB port and the USB hub are compliant with USB 2.0. The scanning speed slows down if the ScanSnap is connected with USB 1.1. If your computer has the USB 2.0 compatible port, use it.

zUsing the Power Cable

1.

 

Connect the power cable

 

 

 

 

 

to the power

 

 

 

connector of the ScanSnap and plug in the

 

 

 

AC outlet.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2.

 

Connect the USB cable

 

 

 

 

to the USB con-

 

 

 

nector on the ScanSnap and the USB port on

 

 

 

your computer.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

zUsing the USB Bus Power Cable

1.

Connect the USB bus power cableto the

 

power connector on the ScanSnap and the

 

USB port on your computer.

 

 

2.

Connect the USB cable

to the USB con-

 

nector on the ScanSnap and the USB port on

 

your computer.

 

 

4. Open the ADF paper chute (cover) of the ScanSnap.[Scan] Button

ADF Paper Chute (Cover)

DThe [Scan] button lights in blue, indicating that the ScanSnap is turned on.

DThe ScanSnap should be automatically detected by your computer.

The bottom part of the ScanSnap may become hot when the ScanSnap is used but this does not affect ScanSnap operation or cause any physical harm. Be careful not to drop the ScanSnap when carrying it.

6