Gardena EVC 1000/30 manual Trouble-Shooting

G

Adjusting for wear:

L

K

1.Remove grass and deposits from wheels, aerator cylinder and housing.

2.Remove dirt from air inlets on the housing.

The Aerator is subject to wear in use due to the way in which it works. The more intensively the Aerator is used, the greater the wear on the knives. Hard or very dry ground accelerates wear as does excessive use of the Aerator.

If the results of your work with the Aerator become increasingly worse due to knife wear, the aerator cylinder can be adjusted twice.

Note: Wear adjustment is not used for height adjustment. Adjustment of the aerator cylinder without visible wear can cause damage to the aerator cylinder or overload the motor.

The aerator cylinder has 3 adjustment positions:

•Position 1: Position set at the factory

•Position 2: First adjustment position after knife wear (aerator cylinder lowered by 3 mm)

•Position 3: Second adjustment position after knife wear (aerator cylinder lowered by a further 3 mm)

The openings for the retainers on the wheels must be free of dirt.

1.Press retaining spring K together and pull out the adjustment unit L approx. 6 mm.

The wheel is no longer fixed to the axle.

2.Turn adjustment unit L 90° to the next highest position.

3.Press the centre of the adjustment unit L until the retaining spring K audibly snaps into the new position.

The wheel is now fixed to the axle in the new position.

4.Adjust the wheel on the other side to the same position.

Both wheels must always be in the same position.

G

N O Q R S

O

5. Push new aerator cylinder onto	O	S P
drive shaft so that the torsion

		bar S fits in the gap in the drive
		shaft P.
O	6.	Lift new aerator cylinder and place
		wheel with end plate N on the
		aerator cylinder.
	7.	Lower wheel with end plate N onto
P		the underside of the housing and, during this process, ensure
		that the parts are not placed under stress.

8.Bolt wheel with end plate N to the underside of the housing using bolts M without over tightening the bolts.

9.Set to wear adjustment position 1

(see 6. Maintenance “Adjusting for wear” ).

Problem	Possible Cause	Remedy
Abnormal noise.	Foreign bodies on the aerator	1.	Switch off the Aerator,
Clattering in the unit	cylinder are hitting the Aerator.		remove the mains plug from
			the socket and wait until the
Whistling sound	Foreign bodies blocking
			Aerator has stopped rotating.
	the aerator cylinder.
		2.	Remove foreign bodies.
	Cogged belt slipping.	v	Contact GARDENA Service.
Motor will not start	Faulty cable.	v	Check cable.
	The conductor cross-section of	v Contact your electrician.
	the extension cable is possibly
	too low.

7. Trouble-Shooting

Motor cuts out because	Blocked by foreign bodies.	1. Switch off the motor,.
blocking protection has		remove the mains plug from
been activated		the socket and wait until

Replacing aerator cylinder:

M

The aerator cylinder can cause injuries !

AV Prior to rectifying faults, unplug from the mains and wait until the aerator cylinder has stopped.

VWear working gloves when rectifying faults.

If the aerator cylinder is in wear adjustment position 3 and is worn, the aerator cylinder must be replaced. It is only permitted to use original GARDENA aerator cylinders.

•GARDENA Aerator Cylinder for Art. No. 4062

1.Undo bolts M on the underside of the housing.

2.Lift wheel with end plate N and remove from aerator cylinder O.

3.Lift aerator cylinder O at an angle and pull off from bar of the drive shaft P.

4.Push new spring Q, new stop, R and new torsion bar S into new aerator cylinder O.

			the Aerator has stopped
			rotating.
		2.	Remove foreign bodies.
		3.	After approx. 1 minute
			switch on the Aerator.
	Aerating depth too large (aerator	1.	Leave motor to cool down.
	cylinder has been adjusted for	2.	Set adjustment for wear
	wear without wear to the knives).		correctly.
	The grass is too tall.	v Mow the lawn before
			aerating (see 3. Function
			“Correct Aerating” ).
Aerating results are not	Aerator cylinder is worn.	v Adjust aerator cylinder
satisfactory			(see Maintenance).
	Cog-belt faulty.	v Allow GARDENA Service
			to change the cog-belt.

18

19