Garland E22-36 installation instructions General Information, Safety, Specifications

Models: E22-36

1 8
Download 8 pages 37.52 Kb
Page 2
Image 2
GENERAL INFORMATION

GENERAL INFORMATION

1.Check the crate for possible damage sustained during transit. Carefully remove the unit from the crate and again check for damage. Any damage to the appliance must be reported to the carrier immediately.

2.The type of voltage supply that the equipment was manufactured for at the factory is noted on the data plate on the equipment. This type of supply must be used.

3.Do not remove permanently affixed labels, warning or data plates form the appliance, this may void approvals and create a safety hazard.

The Garland E22 series complies with the standards CSA C22.2 no. 109 – latest edition and UL197 – latest edition. The installation and connection of this appliance must comply with current codes. In Canada – the Canadian Electrical Code Part 1 and in the USA – the National Electrical Code.

SAFETY

A qualified person must make the installation in accordance with the authority having jurisdiction and local codes.

This unit must only be operated by a qualified person. DO NOT operate without reading this manual.

DO NOT operate this appliance unless all service and access panels are in place and fastened properly.

DO NOT attempt to repair or replace any part of this appliance unless all main power supplies have been disconnected.

DO NOT clean this appliance unless the power supply is disconnected.

WARNING: To avoid serious personal injury:

USE EXTREME CAUTION in setting up, operating and cleaning these appliances to avoid coming in contact with hot surfaces. Wear suitable protective clothing or use proper utensils to prevent the risk of burns.

NOTE: All warning labels and markings on this appliance, which call attention to further dangers and necessary precautions.

SPECIFICATIONS

Models: E22-36-36GM(X) E22-36-45GM(X) E22-36-48GM(X) E22-36-56GM(X)

E22-36-60GM(X) E22-36-68GM(X) E22-36-72GM(X)

X suffix use electronic thermostats

Total kW

 

kW Loading Per Phase

 

 

Nominal Amps Per Phase

 

 

 

 

 

 

 

 

 

 

 

Loading

 

Single Phase

 

 

Three Phase

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

240V

208V

 

240V

 

 

208V

240V

208V

 

240V

 

 

208V

 

 

 

 

 

 

 

 

 

 

 

 

 

X-Y

Y-Z

X-Z

X-Y

Y-Z

X-Z

X

Y

Z

X

Y

Z

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6.7

6.7

3.35

---

3.35

3.35

---

3.35

27.92

32.21

24.22

13.96

13.96

27.95

16.11

16.11

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The E22-36-36GM(X) is for installation in non-combustible locations only. All others should be installed with the following minimum clearances from combustible material.

Minimum Installation Clearances

Left &

Right Sides

Rear

Type of Floor Base

 

 

 

 

1/2”

(12.5mm)

1/2” (12.5mm)

Combustible

 

 

 

 

Page 2

Part # 4517056 (10/04)

Page 2
Image 2
Garland E22-36 installation instructions General Information, Safety, Specifications