Electrical Supply Connection, Siting

INSTALLATION

Electrical Supply:

Before attempting the electrical connection, the rating plate should be checked to ensure the equipment’s electrical characteristics and the supply electrical characteristics agree. On griddles the supply entrance is located at the rear or alternatively on the main bottom. The supply terminal block is accessible from the front. The electrical supply must be adequate for the voltage, phase and current marked on the rating plate.

Note: A means of disconnection from the supply having a contact separation of at least 3 mm in all poles must be incorporated in the ﬁxed wiring.

WARNING: THIS APPLIANCE MUST BE EARTHED

Electrical Supply Connection:

For supply connection, use wire suitable for 75°C (167°F).

A bottom knockout is provided near the front left side of the unit, located behind the control panel. To view the knockout, loosen the four acorn nuts and remove the control panel. The terminal block is also located in this area.

The rear supply cable entrance is located on the right side when facing the rear of the unit. The cable is fed towards the front through the wire way.

Siting:

The base on which the griddle is to be sited must be capable of adequately supporting the weight of the appliance and any ancillary equipment. Once in position, check that the equipment is level, both front and back and side to side. Adjust if necessary.

Ventilation:

This product is to be installed under a ventilation hood.

Proper operation of exhaust fans (proper speed, rotation and adjustment) is essential. In addition a make-up air system for the kitchen to supply fresh air is recommended.

Any ventilation system will break down if improperly maintained. The duct system, the hood, and the ﬁlters must be cleaned on a regular basis and kept grease free.

General Installation Procedure:

1.Carefully remove the unit from the crate. All packing material must be removed from the unit.

2.All griddles are shipped from the factory with leveling feet.

3.Place the griddle in the desired location and level from side to side and back to front.

4.Adequate clearance must be provided for servicing, ventilation and proper operation. The product must be kept free from combustible material.

Commissioning:

1.Ensure all circuit breakers located in the lower compartment are set to the ON (1) position.

2.Ensure that all controls are in the oﬀ position and turn on the main electrical supply.

3.Operate the grill in accordance with the instructions.

4.Check that the product functions correctly and that the voltage supply to the unit does not drop by more than 5% when all sections are operated simultaneously.

When the operation has been checked, hand this instruction manual to the user or purchaser for retention. Instruct them in the eﬃcient and safe operation of the appliance.

Part # 4517056 (10/04)

Page 3

E22-36 specifications

The Garland E22-36 is an innovative and highly efficient piece of agricultural machinery designed to enhance productivity and ease of operation in various farming applications. Known for its robustness and advanced technology, the E22-36 stands out in the market for its unique features and exceptional performance.

One of the primary characteristics of the Garland E22-36 is its powerful engine, which provides an impressive horsepower that allows it to tackle heavy-duty tasks with ease. The engine is engineered for fuel efficiency, ensuring that farmers can operate for extended periods without excessive fuel consumption. This aspect not only reduces operating costs but also minimizes the environmental impact, aligning with contemporary agricultural sustainability practices.

The E22-36 is equipped with an advanced hydraulic system that enables precise control over various implements, such as plows, seeders, and harrows. This hydraulic system enhances the versatility of the machine, allowing it to perform multiple tasks throughout the farming season. The intuitive controls are designed for ease of use, ensuring that operators can manage the machine with minimal training and high efficiency.

In terms of technology, the Garland E22-36 features a state-of-the-art digital dashboard that provides real-time feedback on engine performance, fuel levels, and other critical parameters. This digital interface not only enhances the user experience but also contributes to better maintenance planning by alerting operators to any potential issues before they escalate.

Another notable feature of the E22-36 is its durable construction, which is built to withstand the rigors of daily farming activities. The chassis is made from high-grade materials that resist wear and tear, ensuring longevity and reliability. Furthermore, the adjustable wheelbase allows for improved stability and maneuverability across various terrains, making it suitable for different types of fields.

Safety is also a significant consideration in the design of the E22-36. It is equipped with various safety features, including rollover protection and emergency shut-off mechanisms, which help ensure operators can work confidently and securely.

In conclusion, the Garland E22-36 is a testament to modern agricultural engineering, combining power, efficiency, and versatility. Its advanced features and robust design position it as an indispensable tool for farmers seeking to enhance their operational efficiency while maintaining sustainability in their practices.

Garland E22-36 Electrical Supply Connection, Siting, Ventilation, Commissioning

Models: E22-36