Manuals / Brands / Marine Equipment / Marine GPS System / Garmin / Marine Equipment / Marine GPS System

Garmin 190-01155-00, 720, 720s, 750s Radar Display Appearance, Low, High, Down, Note, Radar, Radar, Medium, Radar Overlay Numbers, 3.Select Menu > Radar Setup > Overlay Numbers

1 100

Download 100 pages, 4.12 Mb

Radar

4.Complete an action:

•Select High, Medium, or Low to decrease or increase the appearance of rain clutter, if using a GMR 20, 21, 40, 41, 18, 18 HD, 24, 24 HD, 404, or 406 radar. Other targets should remain clearly visible on the Radar screen.

•Select Up or Down to decrease or increase the appearance of rain clutter, if using a GMR 604 xHD, 606 xHD, 1204 xHD, or 1206 xHD radar. Other targets should remain clearly visible on the Radar screen. If the FTC setting is greater than 50%, consider reducing the radar range.

5.Select Menu > Noise Rejection > Rain Clutter.

6.Select Up or Down to decrease or increase the appearance of nearby rain clutter until other targets are clearly visible on the Radar screen.

Clutter caused by rain may still be visible.

Adjusting Crosstalk Clutter on the Radar Screen

You can reduce the appearance of clutter caused by interference from another nearby radar source. On is the default value for the crosstalk setting.

Note: Depending upon the radar in use, the crosstalk setting configured for use in one radar mode may or may not be applied to other radar modes or to the Radar Overlay (page 63).

1.From the Home screen, select Radar.

2.Select Cruising, Harbor, Offshore, or Sentry mode.

3.Select Menu > Noise Rejection > Crosstlk > On.

Radar Display Appearance

Radar Overlay Numbers

Overlay numbers with data fields ➊ can appear on all radar modes, and they provide real-time, at-a-glance information. All data bars configured for use in one radar mode appear in every other radar mode. All data bars configured for use on the Radar Overlay appear only on the Radar Overlay, and must be configured separately.

Several radar data overlays are available. You can select the data fields to be shown within each data overlay.

When overlay numbers are displayed on the radar screen, the navigation inset ➋ is shown during navigation. The compass tape ➌ can be shown or hidden in each overlay.

➋

Radar with Data Overlay

Selecting a Data Overlay

1.From the Home screen, select Radar.

2.Select Cruising, Harbor, Offshore, or Sentry mode.

3.Select Menu > Radar Setup > Overlay Numbers.

4.Select or to select a data overlay.

➌

➊

66	GPSMAP 700 Series Owner’s Manual

Contents

Page Page Introduction Tips and Shortcuts Manual Conventions Table of Contents Getting Started Front and Back Panels Turning On the Chartplotter Turning Off the Chartplotter Initial Chartplotter Settings GPS Satellite Signal Acquisition Adjusting the Backlight Adjusting the Color Mode Inserting and Removing Data and Memory Cards Viewing System Information About the Home Screen Charts and 3D Chart Views Navigation Chart Chart Symbols Navigating to a Point on the Chart CAUTION 2.Select Navigation Chart or Fishing Chart 4.Select Navigate To Configuring the Appearance of Waypoint Symbols 3.Select Menu > Waypoints & Tracks > Waypoint Display Label Symbol Only Comment Viewing Tide Station Information 4.Select Navigation Chart Setup or Fishing Chart Setup 5.Select Tides/Currents Animated Viewing Details about Navaids 2.Select Navigation Chart, Fishing Chart, Perspective 3D, or Mariner’s Eye 3D 5.Select Chart Appearance > Detail 5.Select Chart Appearance World Map Full Basic GPS Hdg 5.Select Chart Appearance > Heading Line > Source 2.Select Spot Depths > Dangerous 5.Select Chart Appearance > Symbols Navaid Size Navaid Type NOAA IALA Land POIs Automatic Identification System Other Vessels AIS 3.Select Menu > Other Vessels > AIS Display Setup AIS Display Range Show All Details Show Perspective 3D BlueChart g2 Vision Mariner’s Eye 3D Fish Eye 3D Fishing Chart Showing Satellite Imagery on the Navigation Chart Viewing Aerial Photos of Landmarks Animated Tide and Current Indicators Detailed Road and Point of Interest Data Auto Guidance Combinations About the Combination Screen Combination Screen Configuration 3.Select Menu > Overlay Numbers 5.Select Navigation Inset > Nav. Inset Config Route Leg Details Next Turn 3.Select Menu > Overlay Numbers > Show Compass Tape Using Full-screenView Returning to the Combination Screen from Full-screenView Navigation Basic Navigation Questions Navigation with a Chartplotter Waypoints 4.Select Create Waypoint Edit Waypoint Name Symbol Depth Routes Yes Edit Route Creating and Saving a Route Viewing a List of Saved Routes User Data Tracks Saving the Active Track Midnight •Select Entire Log Save Viewing a List of Saved Tracks Navigating with a Garmin Autopilot Where To Marine Services Destinations Browsing for, and Navigating to, a Saved Waypoint Waypoints Browsing for, and Navigating, a Saved Route Browsing for, and Navigating Parallel to, a Saved Route Forward - Port Forward - Starboard Backward - Port Backward - Starboard Almanac, On-boat,and Environmental Data Almanac Data Current Information Currents 1.From the Home screen, select Information > Currents > Nearby Stations Show Report On-boatData 3.Select Gauge Limits > Custom > Edit Limits Scale Min Scale Max Rated Min Rated Max Use Total Fuel Level 1.From the Home screen, select Information > Dashboard Gauges > Engine > Menu Fill Up All Tanks Set Total Fuel Onboard Trip Gauges Environmental Data •Select GPS Speed •Select Water Speed Speed Display GPS Speed Water Spd Environment Gauges From the Home screen, select Information > Dashboard Gauges > Environment Alignment Device Configuration Basic Device Configuration Questions Simulator Mode Turning the Chartplotter On Automatically Display Configuration Navigation Preferences Safe Depth Safe Height 5.Select Navigate To > Guide To Shoreline Distance Far Farthest Nearest Setting the Heading Reference Units Heading Units of Measure System Units 2.Select Statute (mh, ft, ºF), Metric (kh, m, ºC), or Nautical (kt, ft, ºF) Custom Feet •Select Navigation Chart Setup > Overlay Numbers •Select Fishing Chart Setup > Overlay Numbers •Select Overlay Numbers 6.Select Navigation Inset > Nav. Inset Config Information about Your Boat Alarms Chartplotter Data Management Copying Waypoints, Routes, and Tracks to a Memory Card Add New File 4.Select Save To Card Copying Built-inMaps to a Memory Card Copy Radar Transmitting Radar Signals Adjusting the Zoom Scale on the Radar Screen Radar Display Modes Harbor Mode Offshore Mode Offshore Sentry Mode Sentry Setup 2.Select Stdby Time 5.Select Xmit Time Corner Circle 2.Select Cruising, Harbor, Offshore, Sentry, or Radar Overlay 2.Select Cruising, Harbor, Offshore, or Sentry VRM and EBL 2.Select Cruising, Harbor, or Offshore 3.Select Menu > Show VRM/EBL 3.Select Menu > Adjust VRM/EBL > Move VRM/EBL Waypoints and Routes on the Radar Screen About the Radar Overlay Optimizing the Radar Display About Gain and Clutter 2.Select Cruising, Harbor, Offshore, or Sentry mode 3.Select Menu > Gain > Auto Gain Down 3.Select Menu > Noise Rejection > Sea Clutter > Presets Rough Medium 5.Select Menu > Noise Rejection > Sea Clutter 2.Select Harbor, Offshore, or Sentry mode 3.Select Menu > Noise Rejection > FTC > Off 3.Select Menu > Noise Rejection > Rain Clutter > Off 3.Select Menu > Noise Rejection > FTC Radar Display Appearance 5.Select Navigation Inset 6.Select Nav. Inset Config 4.Select Show Compass Tape Radar Display Settings 1.From the Home screen, select Radar > Radar Setup > Appearance > Color Scheme Radar Navigation Settings From the Home screen, select Radar > Radar Setup > Appearance > Rings > Show Radar Scanner and Antenna Settings Rotation Spd •Select Normal Speed Radar Overlay Display Appearance Radar Overlay Navigation Display Settings Change Distance Sonar Sonar Views Split-zoomSonar View Split Zoom Split-frequencySonar View Split Frequency Changing from One Sonar View to a Different Sonar View Depth Log Transducer Temperature Log Waypoints on the Sonar Screen Sonar Display Appearance Showing Surface Noise Surface Noise Showing and Configuring a Depth Line Depth Line Showing the A-Scope Showing and Configuring the Whiteline Whiteline Setting the Color Scheme •Select Color Scheme > Blue •Select Color Scheme > White Sonar Alarms Transducer Configuration Digital Selective Calling Chartplotter and VHF Radio Functionality Turning On DSC About the DSC List Incoming Distress Calls Man-OverboardDistress Calls Initiated from a VHF Radio Man-OverboardDistress Calls Initiated from the Chartplotter Position Tracking Vessel Trails on the Navigation Chart 3.Select Menu > Other Vessels > DSC Trails 4 Hours 3.Select Menu > Other Vessels > DSC List 5.Select Edit > Trail > Show Individual Routine Calls Making an Individual Routine Call to an AIS Target Appendix Specifications Calibrating the Touchscreen Screenshots Viewing GPS Satellite Locations Using WAAS/EGNOS System Information NMEA 0183 and NMEA Names Numbers Labeling Engines as Names Port (P) Center (C) Selecting a Preferred Data Source 1.From the Home screen, select Configure > Communications > Preferred Sources Transmitting NMEA 0183 Data over a NMEA 2000 Network 1.From the Home screen, select Configure > Communications > Output Bridging Registering Your Device Contacting Garmin Product Support Declaration of Conformity Software License Agreement Index