R E P L A C I N G T H E F I LT E R C L E A N I N G

I N S T R U C T I O N S - S T O R A G E

REPLACING THE FILTERS

1.On average, HEPA filters need to be replaced every 12 - 18 months. Carbon filters need to be replaced every 3 - 6 months. Filter life will vary depending on air quality and usage. Replace filters if punctured.

2.Turn off and unplug the air purifier before attempting to replace the filters.

3.Remove each of the filters from the unit by pulling gen- tly towards you.

4.To replace the carbon filter, simply remove the old car- bon filter and insert a new carbon in its place, using the plastic tabs as a guideline. (See Fig.1)

5.To replace the HEPA filter, discard the old HEPA fil- ters. Put a new carbon filter on the HEPA filter. Insert the new HEPA filter into the unit, by sliding it onto the hang tabs. (See Fig. 2)

6.After replacing the HEPA filters, RESET the filter life monitor by inserting a small object (such as a pin or paper clip) into the hole marked RESET.

NOTE: Carbon and HEPA filters are not washable and should be replaced at the recommended intervals.

PRE-FILTER CLEANING/REPLACEMENT INSTRUCTIONS

1.Every 2-3 weeks, check the condition of the foam pre- filter.

2.Open the front door and remove the Pre-filter frame to examine the pre-filter (fig. 3).

3.If the Pre-filter has a noticeable amount of dust, lint, or particulate accumulation, wash it by hand in warm soapy water. The pre-filter must be washed at least every 30 days or more often as necessary. If the pre-fil- ter is worn or damaged, replace it (go to step 5.). DO

NOT wash in an automatic washer, gently hand wash only.

4.After washing, rinse and dry the pre-filter thoroughly before replacing it into the air purifier door. DO NOT dry the pre-filter in an automatic dryer, hand dry only by dabbing gently with a dry cloth towel.

5.Replace pre-filter in door and latch pre-filter frame (fig.3).

CAUTION: DO NOT OPERATE AIR PURIFIER WITH-

OUT A PRE-FILTER IN PLACE. DIRT AND LINT WILL CLOG IT AND REDUCE PERFORMANCE.

Figure 2

STORAGE INSTRUCTIONS

If your air purifier will not be used for an extended period of time, please follow the below instructions.

1.Turn unit off and unplug.

2.Clean Pre-filter and dry completely. See Pre-filter cleaning instructions.

3.Remove Carbon and HEPA filters and discard.

4.Wipe air purifier clean as in cleaning instructions.

5.Replace Pre-filter.

6.Replace air purifier in original carton and store in a dry cool place.

7.Order Replacement filters for next use.

Figure 3

A

B

A. Pre-Filter Frame

B. Foam Pre-Filter

Page 3 Page 5
Page 4
Image 4
GE 106653, 106643, 106633 warranty Replacing the Filters, Storage Instructions, PRE-FILTER CLEANING/REPLACEMENT Instructions
Page 3 Page 5

106633, 106653, 106643 specifications

GE 106653, 106643, and 106633 are advanced gas turbine models produced by General Electric, aimed at enhancing power generation efficiency and reliability. These models represent a significant leap in turbine technology, incorporating cutting-edge design features and innovative materials.

The GE 106653 gas turbine is known for its high efficiency and environmental performance. It utilizes advanced aerodynamics and materials that allow for a higher combustion temperature, improving the thermal efficiency of power cycles. This model is equipped with a state-of-the-art combustion system that minimizes nitrogen oxide (NOx) emissions, making it an eco-friendly option for power generation in urban environments.

Model 106643 builds on the foundation of its predecessor by integrating enhanced digital technologies. The turbine features advanced sensors and control systems that optimize performance and operational stability. These digital advancements allow for predictive maintenance, monitoring turbine health in real-time, and ensuring maximum uptime. This model is designed with modular components, facilitating easier maintenance and quicker part replacement to reduce downtime.

The 106633 model is designed for a wide range of applications, including industrial power plants and co-generation facilities. Its versatility is one of its main characteristics, capable of operating on various fuels, including natural gas and alternative fuels. The model's design includes a robust airfoil structure that improves aerodynamics and increases output power. Furthermore, it incorporates advanced cooling technologies that enhance material longevity and performance under high-temperatures.

Across all three models, GE has placed a significant emphasis on reducing the environmental footprint of its turbines. Each model features enhanced emission control technologies, ensuring compliance with global standards for emissions and noise reduction.

In summary, GE 106653, 106643, and 106633 gas turbines represent the forefront of energy technology, combining advanced aerodynamics, digital integration, and environmental sustainability. With their high efficiency, low emissions, and innovative designs, these turbines are poised to play a crucial role in meeting global energy demands while promoting a cleaner environment.
Top Page Image Contents