Safety Instructions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.

Instructions Operating Instructions

The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with

a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.

If the outlet is a standard 2-prong outlet, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.

The refrigerator should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate.

This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.

Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.

When moving the refrigerator away from the wall, be careful not to roll over or damage the power cord.

Installation

USE OF ADAPTER PLUGS (Adapter plugs not permitted in Canada)

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an adapter plug.

Troubleshooting Tips

However, if you must use an adapter, where local codes permit, a temporary connection may be made to a properly grounded 2-prong wall outlet by use of a UL-listed adapter available at most local hardware stores.

The larger slot in the adapter must be aligned with the larger slot in the wall outlet to provide proper polarity in the connection of the power cord.

When disconnecting the power cord from the adapter, always hold the adapter in place with one hand while pulling the power cord plug with the other hand. If this is not done, the adapter ground terminal is very likely to break with repeated use.

If the adapter ground terminal breaks, DO NOT USE the refrigerator until a proper ground has been established.

Attaching the adapter ground terminal to a wall outlet cover screw does not ground the appliance unless the cover screw is metal, and not insulated, and the wall outlet is grounded through the house wiring. You should have the circuit checked by a qualified electrician to make sure the outlet is properly grounded.

Consumer Support

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

4

Page 3 Page 5
Page 4
Image 4
GE 200D26000P022 installation instructions HOW to Connect Electricity, Instructions Operating Instructions
Page 3 Page 5

200D26000P022 specifications

The GE 200D26000P022 is a highly advanced and versatile industrial motor designed by General Electric for various heavy-duty applications. Known for its robust performance and durability, this motor is integral to many manufacturing and processing environments.

One of the primary features of the GE 200D26000P022 is its impressive power output, making it suitable for demanding applications that require high torque and efficiency. The motor operates on a high voltage, which allows for significant energy savings and improved operational efficiency. Its design includes a host of advanced engineering features that enhance its performance, including higher speed ratings and excellent thermal management.

Incorporating state-of-the-art technologies, the GE 200D26000P022 integrates permanent magnet motor technology, which enhances its efficiency compared to traditional induction motors. This results in lower energy consumption, reducing operating costs and minimizing the environmental impact. The motor's design also emphasizes minimal maintenance requirements, allowing users to enjoy extended service life with reduced downtime.

Another notable characteristic of the GE 200D26000P022 is its adaptability. This motor can seamlessly be integrated into various applications, including pumps, compressors, and conveyors. Its ability to function in diverse environments, including those with harsh conditions, is a testament to its robust engineering design. The motor is constructed with high-quality materials that provide resistance to corrosion, heat, and mechanical stress.

Additionally, the GE 200D26000P022 is equipped with advanced control systems. These systems allow for precise speed and torque management, enhancing overall operational efficiency. The motor can be controlled using various protocols, making it compatible with numerous industrial automation frameworks. This feature facilitates easier integration into modern smart factories and automation solutions.

In summary, the GE 200D26000P022 stands out for its powerful performance, energy efficiency, and versatility. Its innovative technologies and robust characteristics make it an ideal choice for industries seeking reliable motor solutions capable of handling heavy loads and demanding conditions. As a result, it continues to be a preferred option for professionals in the industrial sector looking to enhance their operations.
Top Page Image Contents