29240
Trimline Phone
User's Guide
We bring good things to life.
EQUIPMENT APPROVAL INFORMATION
Your telephone equipment is approved for connection to the Public Switched Telephone Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the Technical Requirements for Telephone Terminal Equipment published by ACTA.
1Notification to the Local Telephone Company
On the bottom of this equipment is a label indicating, among other information, the US number and Ringer Equivalence Number (REN) for the equipment. You must, upon request, provide this information to your telephone company.
The REN is useful in determining the number of devices you may connect to your telephone line and still have all of these devices ring when your telephone number is called. In most (but not all) areas, the sum of the RENs of all devices connected to one line should not exceed 5. To be certain of the number of devices you may connect to your line as determined by the REN, you should contact your local telephone company.
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.
Notes
•This equipment may not be used on coin service provided by the telephone company.
•Party lines are subject to state tariffs, and therefore, you may not be able to use your own telephone equipment if you are on a party line. Check with your local telephone company.
•Notice must be given to the telephone company upon permanent disconnection of your telephone from your line.
•If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this product does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
2Rights of the Telephone Company
Should your equipment cause trouble on your line which may harm the telephone network, the telephone company shall, where practicable, notify you that temporary discontinuance of service may be required. Where prior notice is not practicable and the circumstances warrant such action, the telephone company may temporarily discontinue service immediately. In case of such temporary discontinuance, the telephone company must: (1) promptly notify you of such temporary discontinuance; (2) afford you the opportunity to correct the situation; and (3) inform you of your right to bring a complaint to the Commission pursuant to procedures set forth in Subpart E of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities, equipment, operations or procedures where such action is required in the operation of its business and not inconsistent with FCC Rules and Regulations. If these changes are expected to affect the use or performance of your telephone equipment, the telephone company must give you adequate notice, in writing, to allow you to maintain uninterrupted service.
INTERFERENCE INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is “receiving” the interference).
•Reorient or relocate and increase the separation between the telecommunications equipment and receiving antenna.
•Connect the telecommunications equipment into an outlet on a circuit different from that to which the receiving antenna is connected.
If these measures do not eliminate the interference, please consult your dealer or an experienced radio/ television technician for additional suggestions. Also, the Federal Communications Commission has prepared a helpful booklet, “How To Identify and Resolve Radio/TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402. Please specify stock number
HEARING AID COMPATIBILITY
This telephone system meets FCC standards for Hearing Aid Compatibility.
US NUMBER IS LOCATED ON THE CABINET BOTTOM
REN NUMBER IS LOCATED ON THE CABINET BOTTOM
INTRODUCTION
Your telephone is designed to give you flexibility in use and high quality performance. To get the most from your new telephone, we suggest that you take a few minutes right now to read through this instruction manual.
CAUTION: When using telephone equipment, there are basic safety instructions that should always be followed. Refer to the IMPORTANT SAFETY INSTRUCTIONS provided with this product and save them for future reference.
BEFORE YOU BEGIN
TELEPHONE JACK REQUIREMENTS | Wall plate |
| |
To use this phone, you need an RJ11C type modular | Modular |
telephone jack, which might look like the one pictured | |
here, installed in your home. If you don’t have a modular | telephone |
jack, call your local phone company to find out how to get | line jack |
one installed. |
|
IMPORTANT INSTALLATION INFORMATION
•Never install telephone wiring during a lightning storm.
•Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
•Never touch uninsulated telephone wires or terminals, unless the telephone line has been disconnected at the network interface.
•Use caution when installing or modifying telephone lines.
•Temporarily disconnect any equipment connected to the phone such as faxes, other phones, or modems.
INSTALLING THE PHONE
Your telephone should be placed on a level surface such as a desk or table
top, or you can mount it on a wall. A desktop/wall mounting pedestal is built into the base of the phone.
1. Slide the RINGER volume switch (on the handset) to the desired volume.
2. Set the receiver volume switch (on the handset) to the desired listening volume.
3. Plug the telephone line cord into a modular wall phone jack.
WALL MOUNT INSTALLATION
Your telephone may also be mounted on a wall plate (not included).
NOTE: To prevent the handset from falling out of the cradle while the phone is hanging on the wall, you must reverse the handset hook (located on the base).
1.Rotate the handset hook tab to an upright position.
2.Push the button on the cradle and pull out the cradle bracket.
3.Rotate bracket 180 degree and put it back on the base.
4.Plug the telephone line cord into a modular wall phone jack.
5.Slip the mounting holes on the base over the wall plate posts and firmly slide the unit down into place (wall plate not included).
WRAPPING THE TELEPHONE LINE CORD
In desktop or wall mount mode, you may want to wrap the excess telephone line cord around the mounting bracket on the bottom of the base.
TELEPHONE OPERATION
Volume switch
MEM buttons
REDIAL button
STORE button
FLASH button
REDIAL
This unit redials up to 32 digits. To automatically redial the last number you called:
1.Pick up the handset and wait for a dial tone.
2.Press the redial button.
FLASH
Press the flash button instead of the hook switch to activate custom calling services such as call waiting or call transfer. Custom calling services are provided by the phone company.
RECEIVER VOLUME
You may control the ringer volume level with the switch located on the side of the handset.
RINGER VOLUME
You may control the ringer volume level with the switch located on the side of the base and handset.
2 = ringer tone will be loud
1 = ringer tone will be low 0 = telephone will not ring.
For numbers stored in one touch memory locations (A, B, C), press the memory location (A, B, or C), and the number dials automatically.
NOTE: Stored numbers are saved using the telephone line power cord. If you disconnect the line cord from the modular phone (wall) jack, the numbers stored in memory are lost.
DELETING A STORED NUMBER FROM MEMORY
1.Press the store button.
2.Press the redial button.
3.Press the store button again.
4.Press the memory location where the number is to be deleted.
CHAIN DIALING
Link several memory locations in sequence by following this example:
Number is For | Memory Location |
Long distance access number | 7 |
Authorization code | 8 |
Frequently called long distance number | 9 |
1.Pick up the handset to get a dial tone.
2.Press the mem button, and then press 7.
3.When you hear the access tone, press the mem button, and then press 8.
4.At the next access tone, press the mem button, and then 9.
IMPORTANT: If you make test calls to emergency numbers, remain on the line and explain the reason for the call to the dispatcher. Also, make these calls in
NOTE: If you make a mistake while storing a number, hang up and repeat the storing procedure.
TROUBLESHOOTING TIPS
No dial tone:
•Press and release the hook switch. Check the hook switch: Does it fully extend when the handset is lifted from the cradle?
Phone doesn’t ring:
•Make sure RINGER switch (located on the handset) is set to loud or low.
•You may have too many extension phones on your line. Unplug some extension phones.
•Check for a dial tone. If there is no dial tone see solutions for "No dial tone."
Other party cannot hear you:
•Make sure phone cord is securely plugged in.
•Make sure extension phones are on the hook at the same time you're using the phone. It is normal for the volume to drop when additional extension phones are used at the same time.
Phone "howls" when handset is placed near base and handset volume level is too high:
• This is normal feedback due to handset volume level being set to maximum.
GENERAL PRODUCT CARE
To keep your telephone working and looking good, follow these guidelines:
•Avoid putting the phone near heating appliances and devices that generate electrical noise (for example, motors or fluorescent lamps).
•DO NOT expose to direct sunlight or moisture.
•Avoid dropping and other rough treatment to the phone.
•Clean with a soft cloth.
•Never use a strong cleaning agent or abrasive powder because this will damage the finish.
•Retain the original packaging in case you need to ship the phone at a later date.
SERVICE
If trouble is experienced with this equipment, for repair or warranty information, please contact customer service at
This product may be serviced only by the manufacturer or its authorized service agents. Changes or modifications not expressly approved by ATLINKS USA, Inc. could void the user’s authority to operate this product. For instructions on how to obtain service, refer to the warranty included in this guide or call customer service at
Or refer inquiries to: ATLINKS USA, Inc.
Manager, Consumer Relations P O Box 1976 Indianapolis, IN 46206
Attach your sales receipt to the booklet for future reference or jot down the date this product was purchased or received as a gift. This information will be valuable if service should be required during the warranty period.
Purchase date _______________________________________________________
Name of store ________________________________________________________
LIMITED WARRANTY
What your warranty covers:
•Defects in materials or workmanship.
For how long after your purchase:
•One year, from date of purchase.
(The warranty period for rental units begins with the first rental or 45 days from date of shipment to the rental firm, whichever comes first.)
What we will do:
•Provide you with a new or, at our option, a refurbished unit. The exchange unit is under warranty for the remainder of the original product’s warranty period.
How you get service:
•Properly pack your unit. Include any cables, etc., which were originally provided with the product. We recommend using the original carton and packing materials.
•”Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the product is within the warranty period, must be presented to obtain warranty service.” For rental firms, proof of first rental is also required. Also print your name and address and a description of the defect. Send via standard UPS or its equivalent to:
ATLINKS USA, Inc. c/o Thomson
11721 B Alameda Ave. Socorro, Texas 79927
•Pay any charges billed to you by the Exchange Center for service not covered by the warranty.
•Insure your shipment for loss or damage. ATLINKS accepts no liability in case of damage or loss.
•A new or refurbished unit will be shipped to you freight prepaid.
What your warranty does not cover:
• | Customer instruction. (Your Owner’s Manual provides information regarding operating instructions |
| and user controls. Any additional information, should be obtained from your dealer.) |
• | Installation and setup service adjustments. |
• | Batteries. |
• | Damage from misuse or neglect. |
• | Products which have been modified or incorporated into other products. |
• | Products purchased or serviced outside the USA. |
• | Acts of nature, such as but not limited to lightning damage. |
WARNING:TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSETHIS PRODUCT TO RAIN OR MOISTURE.
Model 29240 55927860 (Rev. 1 E/S) 04-30
Printed in China
|
|
|
|
|
|
| CAUTION: |
|
|
|
| RISK OF ELECTRIC SHOCK |
|
|
|
| DO NOT OPEN |
|
|
THE LIGHTNING | CAUTION: TO REDUCE THE | THE EXCLAMATION | ||
FLASH AND ARROW | RISK OF ELECTRIC SHOCK, DO | POINT WITHIN THE | ||
HEAD WITHIN THE | NOT REMOVE COVER (OR | TRIANGLE IS A | ||
TRIANGLE IS A | BACK). NO USER | WARNING SIGN | ||
WARNING SIGN | SERVICEABLE PARTS INSIDE. | ALERTING YOU OF | ||
ALERTING YOU OF | REFER SERVICING TO | IMPORTANT | ||
“DANGEROUS | QUALIFIED SERVICE | INSTRUCTIONS | ||
VOLTAGE” INSIDE | PERSONNEL. | ACCOMPANYING | ||
THE PRODUCT. |
|
|
| THE PRODUCT. |
SEE MARKING ON BOTTOM / BACK OF PRODUCT
ATLINKS USA, Inc.
101 West 103rd Street
Indianapolis, IN 46290
© 2004 ATLINKS USA, Inc.
Trademark(s) ® Registered
Marca(s) Registrada(s)
MEMORY
Each memory button is capable of storing phone numbers up to 16 digits.
STORING A NUMBER IN MEMORY
1.Pick up the handset, and press the store button.
2.Dial the number to be stored (up to 16 digits).
3.Press store again.
4.Press a memory location button
INSERTING A PAUSE IN THE DIALING SEQUENCE
Use the redial button to add pauses to a dialing sequence, for example after you dial 9 for an outside line. A pause is approximately 4 seconds long and counts as one of the 16 digits that can be stored in the sequence.
CHANGING A STORED NUMBER
To change a stored number, you just replace it with a different number using the procedure for storing a number.
DIALING A STORED NUMBER
1.Pick up the handset, and wait for a dial tone.
2.For numbers stored in memory locations
Limitation of Warranty:
•THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE HEREBY DISCLAIMED. NO VERBAL OR WRITTEN INFORMATION GIVEN BY ATLINKS USA, INC., ITS AGENTS, OR EMPLOYEES SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY.
•REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER. ATLINKS USA, INC. SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. THIS DISCLAIMER OF WARRANTIES AND LIMITED WARRANTY ARE GOVERNED BY THE LAWS OF THE STATE OF INDIANA. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.
How state law relates to this warranty:
•Some states do not allow the exclusion nor limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts so the above limitations or exclusions may not apply to you.
•This warranty gives you specific legal rights, and you also may have other rights that vary from state to state.
If you purchased your product outside the USA:
•This warranty does not apply. Contact your dealer for warranty information.
