7 4-Wire Conduit Installation, Note Aluminum Wiring | GE JBP45

7 4-Wire Conduit Installation

7 4-Wire Conduit Installation

Remove the 3 screws from the connector block. Remove the grounding strap from the connector block middle location and the screw connecting it to the frame of the range. Insert bare wires between the connector block terminals and movable nuts. Tighten screws securely. Attach ground wire to the frame of the range.

WARNING: Connector block is approved for copper wire connection only. If aluminum wire is used, see note below.

NOTE: ALUMINUM WIRING

a Do not connect aluminum wire to connector block.

Use copper building wire rated for the correct amperage and voltage to make 3 (three) 3″ copper jumper wires. Connect wire as per Step 6 or 7 depending on number of wires.

b Splice copper wires to aluminum wiring using special connector terminals designed and UL-approved for joining copper to aluminum and follow the connector manufacturer’s recommended procedure closely.

Wire used, location and enclosure of splices, etc., must conform to good wiring practices and local codes.

	Screw	Bare wire tips
	Connector block	Bare wire tips
	Connector block
	Connector block terminal
Bare wire		Grounding
Bare wire		plate
Movable nut	Flexible cable
	Flexible cable
	Bracket	Conduit
		Conduit

Safety Information Operating Instructions Installation Instructions Troubleshooting Tips Customer Service

35

Image 35

GE JBP45, JBP46, JBP47 owner manual 7 4-Wire Conduit Installation, Note Aluminum Wiring

Contents

JBP19 JBP21 JBP24 JBP25 JBP26 JBP30 JBP45 JBP46 JBP47 GE AppliancesGE Answer Center Owner’s Manual Write the model and serial numbers here # # Staple sales slip or cancelled check hereCongratulations You Are Now Part of the GE Family Safety Information GE & You A Service PartnershipTroubleshooting Tips If You Need Service WARNING ANTI-TIP DEVICE IMPORTANT SAFETY NOTICEIMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING or using a ventilation fan or hood Safety Information Operating SAFETY PRECAUTIONS Safety Information OVEN WHEN COOKING PORK…Instructions Troubleshooting Tips Customer Service SELF-CLEANING OVEN SURFACE COOKING UNITS Safety Information Operating SAVE THESE INSTRUCTIONS Customer Service Troubleshooting TipsWe want you to remain a happy and healthy part of our GE family REMEMBER… How to Set Using the surface unitsSafety Installation Instructions START TIME ON/OFF Using the oven controlsTIMER ON/OFF AUTOMATIC OVEN Light Oven Temperature Knob Oven Control SettingsOVEN ON Light PREHEATED Light Operating Instructions Using the ovenSafety Information D C B A Aluminum Foil Safety Information Operating Instructions Installation InstructionsPreheating and Pan Placement How to Set the Oven for Broiling Food Broiling guideShelf First Side To Cancel the Timer Using the clock and timerTo Set the Timer To Reset the Timer Make sure the oven clock shows the correct time of day Using the timed baking and roasting featuresAutomatic Stop How to Set a Delay Start and Automatic Stop Troubleshooting Tips Customer Service For Models with Only an Oven Temperature KnobFor Models with Pads and an Oven Temperature Knob Adjust the oven thermostat-Do it yourself How to Set the Oven for Cleaning Using the self-cleaning ovenBefore a Clean Cycle Customer Service Troubleshooting Operating Instructions Installation Instructions How to Delay the Start of CleaningAfter a Clean Cycle Troubleshooting Tips Customer Service Control Panel and Knobs Care and cleaning of the rangeor any reason, be sure the anti-tip device is tipping of the range and cause injury Do not lift the door by the handle Lift-Off Oven DoorTo clean the inside of the door To clean the outside of the door Do not clean the bake element or the broil element Oven Light Replacement on some modelsOven Heating Elements Oven Shelves To remove the storage drawer How to Remove the Storage Drawer or KickPanel to Clean Under the Range Broiler Pan & Grid Lift-Up Cooktop on some models Operating Instructions Safety InformationCustomer Service Troubleshooting Tips Installation Instructions Porcelain Enamel Cooktop Do not clean the surface units in a dishwasher Surface UnitsDrip Pans flat on the drip pan when you plug it back in Before You Begin Installation of the rangeInstallation Instructions for future use BEFORE BEGINNING INSTALLATION 30 ″ 1 Prepare the Openinginstall in either rear corner Not less than the width When moving the range on this type of flooring, it should be installed on a 1/4″ thick sheet of plywood or similar material as follows Flooring Under the Range2 Prepare for Electrical Connection 3 Power Cord Strain Relief Installation Do NOT remove ground strap connection 4 3-Wire Power Cord InstallationConnector block Neutral terminal Ground strap Power cord After 5 4-Wire Power Cord InstallationBefore a Do not connect aluminum wire to the connector block 6 3-Wire Conduit InstallationNOTE ALUMINUM WIRING 7 4-Wire Conduit Installation 10 Final Check 8 Anti-Tip Bracket Installation9 Leveling the Range See the Using the Before you call for service…Troubleshooting Tips Problem See the Broiling guide Customer Service Troubleshooting Tips InstallationInstructions Operating Instructions See the Adjust the oven and timer section See the Using the clock Possible Causes right as far as it will go. Turn Troubleshooting Tips Installation Instructions Operating Instructions Customer Service We Will Replace, At No Charge To You GE Electric Range WarrantyWhat Is Not Covered Safety Information Operating Instructions Special Needs Service Service Telephone NumbersIn-Home Repair Service 800-GE-CARES TDD 800-TDD-GEAC